RADIATOR (w/ EGR Cooler) > INSTALLATION |
| 1. INSTALL RADIATOR ASSEMBLY |
![]() |
Install the radiator with the 4 bolts.
| 2. CONNECT NO. 1 OIL COOLER TUBE INLET (for Automatic Transmission) |
| 3. CONNECT NO. 1 OIL COOLER TUBE OUTLET (for Automatic Transmission) |
| 4. INSTALL FAN SHROUD |
Install the fan pulley to the water pump.
Install the shroud together with the coupling fan between the radiator and engine component.
Install the fluid coupling fan to the fan pulley with the 4 nuts.
Tighten the nuts as much as possible by hand.
![]() |
Attach the shroud's claws to the radiator.
Install the shroud with the 2 bolts.
Install the drive belt .
Tighten the 4 nuts of the fluid coupling fan.
![]() |
Install the radiator reservoir with the 2 bolts.
Connect the No. 1 and No. 2 water by-pass hoses to the tank upper and lower.
![]() |
Install the oil reservoir with the 3 bolts.
| 5. CONNECT RADIATOR HOSE INLET |
| 6. CONNECT RADIATOR HOSE OUTLET |
| 7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 8. ADD ENGINE COOLANT |
Tighten the cylinder block drain cock plug.
Tighten the radiator drain cock plug by hand.
![]() |
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.
| Item | Specified Condition |
| A/T | 11.1 liters (11.7 US qts, 9.8 Imp. qts) |
| M/T | 9.8 liters (10.4 US qts, 8.6 Imp. qts) |
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
![]() |
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
After the coolant cools down, check that the coolant level is at the F line.
If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 9. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester to the radiator reservoir.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks.
If no external leaks are found, check the cylinder block and head.
| 10. INSTALL RADIATOR SIDE DEFLECTOR LH |
![]() |
Install the deflector with the 2 clips and attach the claw.
| 11. INSTALL RADIATOR SIDE DEFLECTOR RH |
Install the deflector with the 2 clips and attach the claw.
| 12. INSTALL RADIATOR GRILLE |
![]() |
Push the radiator grille in the direction indicated by the arrow in the illustration. Attach the 5 claws to install the radiator grille.
Install the 2 screws and 2 clips.
| 13. INSTALL NO. 1 ENGINE UNDER COVER (for 4WD) |
Install the under cover with the 4 bolts.
| 14. PERFORM INITIALIZATION |
Perform initialization (Click here).