RADIATOR > INSTALLATION |
| 1. INSTALL RADIATOR ASSEMBLY |
![]() |
Install the radiator with the 4 bolts.
![]() |
Attach the 4 clamps to the radiator side as shown in the illustration.
Connect the 2 airbag sensor front connectors.
| 2. CONNECT OIL COOLER INLET HOSE (for Automatic Transmission) |
Connect the inlet hose to the radiator tank lower.
| 3. CONNECT OIL COOLER OUTLET HOSE (for Automatic Transmission) |
Connect the outlet hose to the radiator tank lower.
| 4. INSTALL FAN SHROUD |
![]() |
Install the fan pulley to the water pump.
Place the shroud together with the fluid coupling fan between the radiator and engine.
Temporarily install the coupling fan to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.
Attach the shroud's claws to the radiator as shown in A in the illustration.
Install the shroud with the 2 bolts.
Connect the reservoir hose to the radiator tank upper.
Install the drive belt (Click here).
Tighten the 4 nuts of the fluid coupling fan.
| 5. INSTALL AIR PUMP INLET (w/ Secondary Air Injection System) |
![]() |
Install the air inlet with the bolt.
| 6. CONNECT RADIATOR HOSE INLET |
| 7. CONNECT RADIATOR HOSE OUTLET |
| 8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 9. ADD ENGINE COOLANT |
Tighten all the plugs and fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
| Item | Specified Condition | |
| Manual transmission | w/ Heater | 7.8 liters (8.2 US qts, 6.9 Imp. qts) |
| w/o Heater | 7.0 liters (7.4 US qts, 6.2 Imp. qts) | |
| Automatic transmission | w/ Heater | 8.1 liters (8.6 US qts, 7.1 Imp. qts) |
| w/o Heater | 7.3 liters (7.7 US qts, 6.4 Imp. qts) | |
![]() |
Fill the radiator reservoir with TOYOTA Super Long Life Coolant (SLLC) to the F line.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the F line, add TOYOTA SLLC to the F line.
Install the radiator cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2,500 to 3,000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
Check the coolant level in the radiator reservoir.
If the coolant level is below the L line, add SLLC to the reservoir F line.
| 10. CHECK FOR ENGINE COOLANT LEAKS |
Check for engine coolant leaks (Click here).
| 11. INSTALL RADIATOR SIDE DEFLECTOR LH |
![]() |
Install the deflector with the 2 clips and attach the claw.
| 12. INSTALL RADIATOR SIDE DEFLECTOR RH |
Install the deflector with the 2 clips and attach the claw.
| 13. INSTALL RADIATOR GRILLE |
![]() |
Push the radiator grille in the direction indicated by the arrow in the illustration. Attach the 5 claws to install the radiator grille.
Install the 2 screws and 2 clips.
| 14. INSTALL NO. 1 ENGINE UNDER COVER |
Install the cover with the 4 bolts.
| 15. PERFORM INITIALIZATION |
Perform initialization (Click here).