ROOF HEADLINING (for Extra Cab) > INSTALLATION |
| 1. INSTALL NO. 3 SIDE RAIL SPACER REAR LH |
| 2. INSTALL NO. 3 SIDE RAIL SPACER REAR RH |
| 3. INSTALL NO. 2 SIDE RAIL SPACER REAR LH |
| 4. INSTALL NO. 2 SIDE RAIL SPACER REAR RH |
| 5. INSTALL SIDE RAIL SPACER REAR LH (for LHD) |
| 6. INSTALL SIDE RAIL SPACER REAR RH (for RHD) |
| 7. INSTALL SIDE RAIL SPACER FRONT LH |
| 8. INSTALL SIDE RAIL SPACER FRONT RH |
| 9. INSTALL NO. 2 ROOF SILENCER PAD |
| 10. INSTALL ROOF HEADLINING ASSEMBLY |
![]() |
Align the wire harness to the markings, and then install the wire harness with tape.
Install the roof headlining with the 5 clips.
| 11. INSTALL ASSIST GRIP |
Install the assist grip with the 2 screws.
Close the 2 covers.
| 12. INSTALL VISOR HOLDER LH |
![]() |
Attach the 2 claws to install the holder.
Install the screw.
| 13. INSTALL VISOR HOLDER RH |
| 14. INSTALL VISOR ASSEMBLY LH |
Install the visor with the screw.
| 15. INSTALL VISOR ASSEMBLY RH |
Install the visor with the screw.
| 16. INSTALL NO. 1 ROOM LIGHT ASSEMBLY |
![]() |
Connect the light connector.
Install the room light with the 2 screws.
| 17. INSTALL NO. 1 ROOM LIGHT LENS |
![]() |
Attach the lens with the 4 claws.
| 18. INSTALL ROOF SIDE GARNISH INNER UPPER LH |
![]() |
Attach the 3 clips to install the garnish.
![]() |
Connect the rear No. 1 seat belt's shoulder anchor.
Connect the shoulder anchor with the bolt.
Attach the 2 claws to close the cover.
| 19. INSTALL ROOF SIDE GARNISH INNER UPPER RH |
| 20. INSTALL QUARTER PILLAR GARNISH LH |
![]() |
Connect the front seat outer belt's shoulder anchor.
Connect the shoulder anchor with the bolt.
Attach the 4 claws to install the seat belt anchor cover cap.
![]() |
Attach the 2 clips to install the garnish.
| 21. INSTALL QUARTER PILLAR GARNISH RH |
| 22. INSTALL QUARTER INSIDE TRIM BOARD LH |
![]() |
Attach the claws and install the trim pocket to the trim board.
Attach the 7 clips and 6 claws to install the trim board.
![]() |
Connect the front seat outer belt's anchor with the bolt.
![]() |
Connect the rear No. 1 seat belt's anchor with the built-in bolt.
| 23. INSTALL QUARTER INSIDE TRIM BOARD RH |
| 24. INSTALL REAR SEATBACK ASSEMBLY |
![]() |
Place the seat in the cabin.
Attach the seatback's 2 hooks to the vehicle body.
Install the seat with the 2 bolts.
| 25. INSTALL BACK PANEL GARNISH LOWER |
![]() |
Attach the 5 clips and 6 claws to install the garnish.
| 26. INSTALL REAR SEAT CUSHION ASSEMBLY LH (w/ Seat Cushion) |
![]() |
Attach the seat cushion's 2 rear hooks to the vehicle body.
![]() |
Attach the seat cushion's front hook to the rear seat cushion lock hook. Then install the seat cushion.
Confirm that the seat cushion is firmly installed.
| 27. INSTALL REAR SEAT CUSHION ASSEMBLY RH (w/ Seat Cushion) |
| 28. INSTALL BACK PANEL GARNISH UPPER |
![]() |
Attach the 5 clips and 4 claws to install the garnish.
| 29. INSTALL FRONT PILLAR GARNISH LH |
![]() |
Attach the 2 clips and 2 claws to install the garnish.
w/ Assist grip:
Install the assist grip with the 2 screws.
w/ Assist grip:
Attach the 4 claws to install the 2 assist plugs.
| 30. INSTALL FRONT PILLAR GARNISH RH |
| 31. INSTALL COWL SIDE TRIM BOARD LH |
![]() |
Attach the 2 clips to install the trim board.
Install the cap nut.
| 32. INSTALL COWL SIDE TRIM BOARD RH |
| 33. INSTALL FRONT DOOR OPENING TRIM LH |
| 34. INSTALL FRONT DOOR OPENING TRIM RH |
| 35. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Attach the 4 clips and 8 claws to install the scuff plate.
| 36. INSTALL FRONT DOOR SCUFF PLATE RH |
| 37. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 38. PERFORM INITIALIZATION |
Perform initialization (Click here).