Home › BODY › INTERIOR › ROOF HEADLINING (for Double Cab)

ROOF HEADLINING (for Double Cab) > INSTALLATION

for Preparation Click here



1. INSTALL NO. 3 SIDE RAIL SPACER REAR LH


2. INSTALL NO. 3 SIDE RAIL SPACER REAR RH


3. INSTALL NO. 2 SIDE RAIL SPACER REAR LH
  1. Install the 2 spacers.



4. INSTALL NO. 2 SIDE RAIL SPACER REAR RH
  1. Install the 2 spacers.



5. INSTALL SIDE RAIL SPACER REAR LH
  1. LHD, w/o Rear roof assist grip:
    Install the 2 spacers.

  1. LHD, w/ Rear roof assist grip:
    Install the spacer.

  1. RHD, w/o Rear roof assist grip:
    Install the spacer.



6. INSTALL SIDE RAIL SPACER REAR RH
  1. LHD, w/o Rear roof assist grip:
    Install the spacer.

  1. RHD, w/o Rear roof assist grip:
    Install the 2 spacers.

  1. RHD, w/ Rear roof assist grip:
    Install the spacer.



7. INSTALL SIDE RAIL SPACER FRONT LH


8. INSTALL SIDE RAIL SPACER FRONT RH


9. INSTALL ROOF NO. 2 SILENCER PAD
  1. Install the 2 silencer pads.



10. INSTALL ROOF HEADLINING ASSEMBLY


    B122941E01
  1. Align the wire harness to the markings, and then install the wire harness with tape.

    NOTICE:
    Attach the roof wire harness securely.



    B122940E01
  1. w/o Rear roof assist grip:
    Install the roof headlining with the 9 clips.

  1. w/ Rear roof assist grip:
    Install the roof headlining with the 5 clips.



11. INSTALL ASSIST GRIP


B111748E01
  1. w/o Rear roof assist grip:
    Install the assist grip with the 2 screws.

  1. w/o Rear roof assist grip:
    Close the 2 covers.

  1. w/ Rear roof assist grip:
    Install the 3 assist grips with the 6 screws.

  1. w/o Rear roof assist grip:
    Close the 6 covers.



12. INSTALL VISOR HOLDER LH


B111747
  1. Attach the 2 claws to install the holder.

  1. Install the screw.



13. INSTALL VISOR HOLDER RH

HINT:
Use the same procedures described for the LH side.



14. INSTALL VISOR ASSEMBLY LH
  1. Install the visor with the screw.



15. INSTALL VISOR ASSEMBLY RH
  1. Install the visor with the screw.



16. INSTALL NO. 1 ROOM LIGHT ASSEMBLY


B085593
  1. Connect the light connector.

  1. Install the room light with the 2 screws.



17. INSTALL NO. 1 ROOM LIGHT LENS


B085012E01
  1. Attach the lens with the 4 claws.



18. INSTALL MAP LIGHT ASSEMBLY (w/ Personal Light)


B117646
  1. Install the bulb to the light.

  1. Connect the connector.

  1. Attach the map light as shown in the illustration.

  1. Install the 2 screws.



19. INSTALL QUARTER INSIDE TRIM BOARD LH


B085560E01
  1. Attach the 4 clips to install the trim board.



    B087825E02
  1. Connect the rear No. 1 seat belt's shoulder anchor.

    1. Connect the shoulder anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Attach the 2 claws to close the cover.



20. INSTALL QUARTER INSIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



21. INSTALL QUARTER TRIM PANEL LOWER LH


B085565E02
  1. Attach the 3 clips and claw to install the trim panel.



22. INSTALL QUARTER TRIM PANEL LOWER RH

HINT:
Use the same procedures described for the LH side.



23. INSTALL BACK PANEL TRIM (w/ Back Panel Trim)
  1. Install the back panel trim with the 3 clips.



24. INSTALL BACK PANEL GARNISH UPPER


B086202E01
  1. Attach the 5 clips and 4 claws to install the garnish.



25. INSTALL FRONT PILLAR GARNISH LH


B111746E01
  1. Attach the 2 clips and 2 claws to install the garnish.

  1. w/ Assist grip:
    Install the assist grip with the 2 screws.

  1. w/ Assist grip:
    Attach the 4 claws to install the 2 assist plugs.



26. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



27. INSTALL CENTER PILLAR GARNISH LH


    B084920E04
  1. Connect the front seat outer belt's shoulder anchor.

    1. Connect the shoulder anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Attach the 4 claws to install the seat belt anchor cover cap.



    B085561E02
  1. Attach the clip and claw to install the garnish.



28. INSTALL CENTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



29. INSTALL CENTER PILLAR GARNISH LOWER LH


    B085563E01
  1. Attach the 2 clips and 2 claws to install the garnish.



    B085693E02
  1. Connect the front seat outer belt's anchor with built-in bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



30. INSTALL CENTER PILLAR GARNISH LOWER RH

HINT:
Use the same procedures described for the LH side.



31. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


32. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


33. REMOVE REAR DOOR SCUFF PLATE LH


B085564E01
  1. Attach the 2 clips and 7 claws to install the scuff plate.



34. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



35. INSTALL COWL SIDE TRIM BOARD LH


B085566E01
  1. Attach the 2 clips to install the trim board.

  1. Install the cap nut.



36. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



37. INSTALL FRONT DOOR OPENING TRIM LH


38. INSTALL FRONT DOOR OPENING TRIM RH


39. INSTALL FRONT DOOR SCUFF PLATE LH


B085562E01
  1. Attach the 3 clips and 7 claws to install the scuff plate.



40. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



41. INSTALL REAR SEAT ASSEMBLY
  1. Install the rear seat (Click here).



42. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


43. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.