COMMON RAIL (w/o EGR Cooler) > INSTALLATION |
| 1. INSTALL COMMON RAIL ASSEMBLY |
![]() |
Install the common rail with the 2 bolts.
Connect the fuel pressure sensor connector.
| 2. INSTALL FUEL INLET PIPE SUB-ASSEMBLY |
![]() |
Temporarily install the fuel inlet pipe with the union nuts.
Using a 17 mm union nut wrench, tighten the inlet pipe union nut on the common rail side.
Using a 17 mm union nut wrench, tighten the inlet pipe union nut on the supply pump side.
Install the oil dipstick guide with the bolt.
![]() |
Install the clamp with the bolt.
| 3. INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY |
![]() |
Temporarily install the leakage pipe with the 3 bolts.
Temporarily install a new gasket with the check valve.
Fully tighten the 3 bolts and check valve.
Connect the 2 fuel hoses.
| 4. INSTALL INJECTION PIPE |
![]() |
Temporarily install the No. 1, No. 2 and No. 3 injection pipes with the union nuts.
Install the No. 2 and No. 3 injection pipe clamps with the bolt and 2 nuts, as shown in the illustration.
![]() |
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
![]() |
Temporarily install the No. 4 injection pipe with the union nuts.
Install 2 new injection pipe clamps with the 2 bolts.
![]() |
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
| 5. INSTALL OIL FILTER SUB-ASSEMBLY |
Check and clean the oil filter installation surface.
Apply clean engine oil to the gasket of a new oil filter.
Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.
![]() |
Using SST, tighten the oil filter. Depending on the work space available, choose from the following.
If enough space is available, use a torque wrench to tighten the oil filter.
If enough space is not available to use a torque wrench, tighten the oil filter 3/4 turn by hand or with a common wrench.
| 6. INSTALL MANIFOLD STAY |
![]() |
Install the stay with the 2 bolts.
| 7. INSTALL NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY |
![]() |
Connect the pipe (with the 2 air hoses) and install the bolt.
Tighten the 2 clamps of the No. 1 and No. 2 air hoses.
Connect the vacuum hose to the gas filter.
Connect the manifold absolute pressure sensor connector.
| 8. ADD FUEL |
| 9. TIGHTEN FUEL TANK CAP ASSEMBLY |
| 10. ADD ENGINE OIL |
| 11. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump, bleed air from the fuel system until pumping becomes difficult.
| 12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 13. PERFORM INITIALIZATION |
Perform initialization (Click here).
| 14. CHECK FOR ENGINE OIL LEAKS |
| 15. CHECK FOR FUEL LEAKS |
| 16. INSTALL NO. 2 ENGINE UNDER COVER (for 4WD) |
Install the under cover with the 2 bolts.
| 17. INSTALL NO. 1 ENGINE UNDER COVER (for 4WD) |
Install the under cover with the 2 bolts.