OIL PUMP (w/o EGR Cooler) > REMOVAL |
| 1. REMOVE ENGINE ASSEMBLY |
| 2. REMOVE NO. 1 TIMING BELT COVER |
Remove the bolt and water hose clamp.
Remove the wire harness clamp.
![]() |
Remove the 6 bolts and timing belt cover.
| 3. REMOVE TIMING BELT |
![]() |
Turn the crankshaft clockwise and align the timing marks as shown in the illustration.
![]() |
Uniformly loosen the 2 bolts and remove the timing belt tensioner.
Remove the timing belt.
Using a 10 mm hexagon wrench, remove the bolt, timing belt idler and washer.
![]() |
| 4. REMOVE VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 2 bolts and viscous with magnet clutch heater assembly.
| 5. REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY |
Remove the 4 bolts and No. 1 viscous heater bracket.
| 6. REMOVE NO. 2 IDLE PULLEY ASSEMBLY |
| 7. REMOVE GENERATOR ASSEMBLY |
![]() |
Remove the nut and generator wire.
Disconnect the generator connector.
Remove the 2 bolts and generator.
| 8. REMOVE GENERATOR BRACKET |
Remove the bolt and generator bracket.
| 9. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Remove the 4 bolts and V-ribbed belt tensioner.
| 10. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET |
Remove the 4 bolts and No. 1 compressor mounting bracket.
| 11. REMOVE MANIFOLD STAY |
Disconnect the 3 vacuum hoses from the 2 VSV.
![]() |
Remove the 2 bolts and stay.
| 12. REMOVE FUEL INLET PIPE SUB-ASSEMBLY |
Remove the engine oil level dipstick.
![]() |
Remove the bolt and clamp.
Remove the bolt and engine oil level dipstick guide.
Remove the O-ring engine oil level dipstick guide.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
| 13. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY |
![]() |
Remove the bolt and No. 2 injection pipe clamp.
Remove the 2 nuts and No. 3 injection pipe clamp.
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
| 14. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY |
![]() |
Remove the 2 bolts.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
| 15. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Disconnect the ventilation hose.
Disconnect the 4 injector connectors.
![]() |
Using a small screwdriver, remove the 4 nozzle holder seals by prying the portion between each nozzle holder seal and the cutout part of the cylinder head cover.
![]() |
Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.
| 16. REMOVE CAMSHAFT TIMING PULLEY |
![]() |
Remove the bolt of the camshaft timing pulley by holding the camshaft with a wrench.
Remove the camshaft timing pulley.
| 17. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY |
| 18. REMOVE NO. 2 TIMING BELT COVER |
Remove the 4 bolts, nut and timing belt cover.
| 19. REMOVE WATER PUMP ASSEMBLY |
![]() |
Remove the 5 bolts, 2 nuts, water pump and gasket.
| 20. REMOVE VACUUM PUMP ASSEMBLY |
![]() |
Remove the 2 nuts, vacuum pump and 2 O-rings.
| 21. REMOVE VANE PUMP ASSEMBLY |
![]() |
Remove the 2 nuts, vane pump and O-ring.
| 22. REMOVE PUMP DRIVE SHAFT PULLEY |
![]() |
Remove the 4 bolts, No. 2 camshaft timing pulley flange and pump drive shaft pulley.
![]() |
Using SST, hold the crankshaft pulley and remove the nut and O-ring.
| 23. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, remove the pulley bolt.
![]() |
Using SST, remove the pulley.
| 24. REMOVE CAMSHAFT POSITION SENSOR |
Remove the bolt and camshaft position sensor.
| 25. REMOVE CRANKSHAFT POSITION SENSOR |
Remove the bolt and crankshaft position sensor.
| 26. REMOVE TIMING GEAR COVER |
![]() |
Remove the wire harness clamp.
Remove the 14 bolts and 2 nuts.
Using a slotted screwdriver, gently separate the cover from the timing gear case.
Remove the cover and O-ring.
| 27. REMOVE NO. 1 IDLE GEAR |
![]() |
Secure the No. 2 idle sub gear to the No. 1 idle gear with a service bolt.
Remove the 2 bolts and thrust plate.
Remove the service bolt.
Turn the No. 2 idle sub gear and align the gear teeth of the No. 1 idle gear and No. 2 idle sub gear.
Remove the No. 1 idle gear together with the No. 2 idle sub gear.
Remove the idle gear shaft.
| 28. REMOVE CRANKSHAFT TIMING GEAR |
![]() |
Remove the No. 1 crankshaft sensor plate.
![]() |
Using SST, remove the crankshaft timing gear.
| 29. REMOVE INJECTION GEAR |
![]() |
Using SST, remove the injection gear.
| 30. REMOVE FUEL SUPPLY PUMP ASSEMBLY |
![]() |
Remove the bolt and clamp.
Remove the 2 bolts and oil level gauge guide.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
![]() |
Disconnect the 2 fuel hoses.
![]() |
Disconnect the 2 connectors.
![]() |
Remove the 4 bolts indicated by the arrows in the illustration.
Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.
![]() |
Remove the set nut and O-ring while holding the crankshaft pulley by using SST.
![]() |
Loosen the 2 nuts.
![]() |
Using SST, disconnect the pump from the injection gear.
Remove the 2 nuts and pump.
Remove the O-ring.
| 31. REMOVE ENGINE OIL LEVEL DIPSTICK |
| 32. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE |
Remove the bolt and dipstick guide.
Remove the O-ring from the dipstick guide.
| 33. REMOVE OIL PAN SUB-ASSEMBLY |
Remove the 22 bolts and 2 nuts.
![]() |
Insert the blade of an oil pan seal cutter between the cylinder block and oil pan. Cut through the applied sealer and remove the oil pan.
Clean off any sealer remaining on the oil pan and cylinder block.
| 34. REMOVE OIL STRAINER SUB-ASSEMBLY |
Remove the 2 bolts, nut, oil strainer and gasket.
| 35. REMOVE TIMING GEAR CASE ASSEMBLY |
Remove the nut and No. 1 vacuum transmitting pipe.
![]() |
Remove the 8 bolts and union bolt. Then remove the timing gear case and 2 O-rings.
Remove the gasket.