ENGINE OIL COOLER (w/ EGR Cooler) > INSTALLATION |
| 1. INSTALL OIL COOLER ASSEMBLY |
Install 2 new gaskets to the oil cooler.
![]() |
Install the oil cooler to the oil cooler cover with the 4 nuts.
| 2. INSTALL OIL COOLER COVER SUB-ASSEMBLY |
![]() |
Install a new gasket and the oil cooler cover with the 13 bolts.
Install the No. 2 vacuum transmitting pipe with the 2 nuts.
Connect the oil pressure connector and wire harness.
| 3. INSTALL OIL FILTER SUB-ASSEMBLY |
Check and clean the oil filter installation surface.
Apply clean engine oil to the gasket of a new oil filter.
Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.
![]() |
Using SST, tighten the oil filter. Depending on the work space available, choose from the following.
If enough space is available, use a torque wrench to tighten the oil filter.
If enough space is not available to use a torque wrench, tighten the oil filter 3/4 turn by hand or with a common wrench.
| 4. INSTALL FUEL SUPPLY PUMP ASSEMBLY |
![]() |
Check that the supply pump gear in the timing gear case moves back and forth smoothly.
Install a new O-ring to the pump.
Apply a light coat of engine oil to the O-ring.
![]() |
Align the set key on the drive shaft with the groove of the injection gear.
![]() |
Install the pump with the 2 nuts.
Set a new O-ring.
![]() |
Using SST, hold the crankshaft pulley and install the set nut.
![]() |
Using a dial indicator, measure the thrust clearance of the injection pump shaft by moving the pump drive shaft pulley back and forth.
![]() |
Connect the 2 connectors.
![]() |
Connect the 2 fuel hoses.
| 5. INSTALL STARTER ASSEMBLY |
![]() |
Connect the ground wire and install the starter with the 2 bolts.
Install the starter wire to terminal 30 with the nut.
Connect the starter connector.
| 6. INSTALL COMMON RAIL ASSEMBLY |
![]() |
Install the common rail and insulator with the 2 bolts.
Connect the 2 connectors.
| 7. INSTALL NO. 2 INTAKE MANIFOLD INSULATOR |
| 8. INSTALL FUEL INLET PIPE SUB-ASSEMBLY |
![]() |
Temporarily install the fuel inlet pipe with the union nuts.
Install a new O-ring to the oil level gauge guide, and install the oil level gauge guide to the cylinder block.
![]() |
Temporarily install the stay of the oil level gauge guide to the intake manifold with the bolt.
![]() |
Install the clamp with the bolt.
Tighten the bolt of the oil level gauge guide stay.
![]() |
Using a 17 mm union nut wrench, tighten the injection pipe union nut on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nut on the supply pump side.
| 9. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY |
![]() |
Temporarily install the leakage pipe with the 3 bolts.
Temporarily install a new gasket with the check valve.
Tighten the 3 bolts and check valve.
Connect the 3 fuel hoses.
| 10. INSTALL OIL DIPSTICK GUIDE |
![]() |
Install a new O-ring to the guide.
Apply a small amount of clean engine oil to the O-ring.
Install the guide with the bolt.
Install the injection pipe clamp with the bolt.
| 11. INSTALL NO. 4 INJECTION PIPE |
![]() |
Temporarily install the No. 4 injection pipe with the union nuts.
Install new injection pipe clamp with the bolt.
![]() |
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.
Using a union nut wrench, tighten the injection pipe union nuts on the injector side.
| 12. INSTALL EGR COOLER WITH ELECTRIC EGR CONTROL VALVE AND NO. 2 EGR VALVE |
Install the EGR cooler with electric EGR control valve and No. 2 EGR valve (Click here).
| 13. INSTALL MANIFOLD STAY |
![]() |
Install the manifold stay with VSV with the 2 bolts, and connect the No. 1 vacuum transmitting hose (color is "Blue") to the No. 2 vacuum transmitting pipe.
![]() |
Connect the 3 vacuum hoses.
![]() |
Connect the 2 connectors.
| 14. ADD FUEL |
| 15. INSTALL FUEL TANK CAP ASSEMBLY |
| 16. BLEED AIR FROM FUEL SYSTEM |
| 17. ADD ENGINE OIL |
Wipe the oil pan and drain plug.
Install a new gasket and the drain plug.
Add new oil.
| Item | Specified Condition |
| Drain and refill with oil filter change | 6.9 liters (7.3 US qts, 6.1 Imp. qts) |
| Drain and refill without oil filter change | 6.6 liters (7.0 US qts, 5.8 Imp. qts) |
| Dry fill | 7.4 liters (7.8 US qts, 6.5 Imp. qts) |
Install the oil filler cap.
| 18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 19. INSPECT FOR FUEL LEAK |
![]() |
Check that there are no leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.
Start the engine and check that there are no leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.
Disconnect the return hose from the common rail.
Start the engine and check for fuel leaks from the return pipe.
If there is fuel leakage, replace the common rail.
Connect the intelligent tester to the DLC3.
Start the engine and push the intelligent tester main switch ON.
Select the Fuel Leak test from the Active Test mode on the intelligent tester.
If the intelligent tester is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.
Check that there are no leaks from any part of the fuel system.
Reconnect the return hose to the common rail.
| 20. ADD ENGINE COOLANT |
Tighten the cylinder block drain cock plug.
Tighten the radiator drain cock plug by hand.
![]() |
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.
| Item | Specified Condition |
| A/T | 11.1 liters (11.7 US qts, 9.8 Imp. qts) |
| M/T | 9.8 liters (10.4 US qts, 8.6 Imp. qts) |
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
![]() |
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
After the coolant cools down, check that the coolant level is at the F line.
If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 21. INSPECT FOR OIL LEAK |
| 22. CHECK ENGINE OIL LEVEL |
| 23. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester to the radiator reservoir.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks.
If no external leaks are found, check the cylinder block and head.
| 24. INSTALL NO. 2 ENGINE UNDER COVER (for 4WD) |
Install the under cover with the 2 bolts.
| 25. INSTALL NO. 1 ENGINE UNDER COVER (for 4WD) |
Install the under cover with the 4 bolts.
| 26. PERFORM INITIALIZATION |
Perform initialization (Click here).