Home › ENGINE ยท 1KD-FTV › LUBRICATION › ENGINE OIL COOLER (w/o EGR Cooler)

ENGINE OIL COOLER (w/o EGR Cooler) > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE NO. 1 ENGINE UNDER COVER (for 4WD)
  1. Remove the 4 bolts and under cover.



3. REMOVE NO. 2 ENGINE UNDER COVER (for 4WD)
  1. Remove the 2 bolts and under cover.



4. DRAIN ENGINE OIL
  1. Remove the oil filter cap.

  1. Remove the oil drain plug, and drain the engine oil from the oil pan.

    NOTICE:
    Collect the oil in an oil disposal container.



5. LOOSEN FUEL TANK CAP ASSEMBLY


6. DRAIN FUEL


7. REMOVE MANIFOLD STAY


G037596E01
  1. Remove the 2 bolts and stay.



8. REMOVE OIL LEVEL GAUGE SUB-ASSEMBLY
  1. Remove the bolt and gauge.

  1. Remove the O-ring from the gauge.



9. REMOVE FUEL INLET PIPE SUB-ASSEMBLY


G036615E01
  1. Remove the bolt and clamp.

  1. Remove the 2 bolts and oil level gauge guide.



    A098969E06
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.



10. REMOVE INJECTION PIPE


A098967E06

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. Remove the 2 nuts and No. 3 injection pipe clamp.

  1. Remove the bolt and No. 2 injection pipe clamp.



  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.



      A098893E01
    1. Remove the 2 bolts and disconnect the 2 injection pipe clamps.



    2. A098968E06
    3. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.



11. REMOVE OIL FILTER SUB-ASSEMBLY


B011502E01
  1. Using SST, remove the oil filter.

    SST
    09228-07501  

    HINT:
    Insert the drain hose in the oil filter. Put the drain oil container beneath the drain hose to collect the oil from the oil filter.



12. REMOVE STARTER ASSEMBLY
  1. for A340F A340E:
    Remove transmission oil filler tube sub-assembly.

    1. Remove the oil level dipstick.

    2. Remove the 2 bolts and transmission oil filler tube sub-assembly.

    3. Remove the O-ring from the transmission oil filler tube sub-assembly.



    A111843
  1. Disconnect the starter connector.

  1. Remove the nut and disconnect the starter wire.



    A122908
  1. A/T:
    Remove the 2 nuts, bolt, and disconnect the ground cable.



    A122907
  1. M/T:
    Remove the nut, bolt, and disconnect the ground cable.

  1. Remove the starter.



13. REMOVE FUEL SUPPLY PUMP ASSEMBLY


G036615E01
  1. Remove the bolt and clamp.

  1. Remove the 2 bolts and oil level gauge guide.



    A098969E05
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.



    A098895E01
  1. Disconnect the 2 fuel hoses.



    A098896E01
  1. Disconnect the 2 connectors.



    A070710E01
  1. Remove the 4 bolts indicated by the arrows in the illustration.

  1. Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.



    A070711E02
  1. Remove the set nut and O-ring while holding the crankshaft pulley by using SST.

    SST
    09213-58013  
    09330-00021  



    A098897E01
  1. Loosen the 2 nuts.



    A070714E01
  1. Using SST, disconnect the pump from the injection gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply lubricant to the threads and tip of SST (center bolt) before using it.

  1. Remove the 2 nuts and pump.

    NOTICE:
    1. Do not hold the pump or carry it holding the pipe.
    2. The pump must be kept horizontal.

  1. Remove the O-ring.



14. REMOVE COMMON RAIL ASSEMBLY


A098899E01
  1. Disconnect the fuel pressure sensor connector.

  1. Remove the 2 bolts and common rail.

    NOTICE:
    Do not remove the pressure limiter and pressure sensor.



15. REMOVE OIL COOLER COVER SUB-ASSEMBLY


A038741E01
  1. Disconnect the oil pressure switch connector and wire harness.

  1. Remove the 13 bolts, 2 nuts and oil cooler cover.



16. REMOVE OIL COOLER ASSEMBLY
  1. Loosen the 4 nuts first.

  1. Partially tap out the oil cooler by tapping each nut head with a plastic-faced hammer.

  1. Remove the 4 nuts, oil cooler and 2 gaskets.