Home › ENGINE · 1KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/ EGR Cooler)

DTC    P0100    Mass or Volume Air Flow Circuit

DTC    P0102    Mass Air Flow Circuit Low

DTC    P0103    Mass Air Flow Circuit High

for Preparation Click here


DESCRIPTION

The mass air flow meter uses a platinum hot wire. The mass air flow meter consists of a platinum hot wire, a temperature sensor and a control circuit installed in a plastic housing. The mass air flow meter works on the principle that the hot wire and temperature sensor located in the intake air by-pass of the housing detect any changes in the intake air temperature.
The hot wire is maintained at the predetermined temperature by controlling the current flow through the hot wire. This current flow is then related as the output voltage of the mass air flow meter.
The circuit is constructed so that the platinum hot wire and temperature sensor provide a bridge circuit, with the power transistor controlled so that the potential of A and B remains equal to maintain the predetermined temperature.

A085670E02


DTC No.
DTC Detection Condition
Trouble Area
P0100
Open or short in mass air flow meter circuit for more than 3 seconds with engine speed at 2,000 rpm or less
(1 trip detection logic)
  1. Open or short in mass air flow meter circuit
  2. Mass air flow meter
  3. ECM
P0102
Open in mass air flow meter circuit for more than 3 seconds with engine speed at 2,000 rpm or less
(1 trip detection logic)
P0103
Short in mass air flow meter circuit for more than 3 seconds with engine speed at 2,000 rpm or less
(1 trip detection logic)

HINT:
After confirming DTC P0100, P0102 or P0103, check the mass air flow ratio in the following menus: Powertrain / Engine / Data List / MAF using the intelligent tester.


Reference:

Air Flow Value (gm/sec.)
Malfunction
Approximately 0.0
  1. Open in mass air flow meter power source circuit
  2. Open or short in VG circuit
174.0 or more
Open in EVG circuit


WIRING DIAGRAM


A154843E03


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (MAF)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / MAF

  1. Read the value.

    Result:

    Air flow rate (gm/sec.)
    Proceed to
    0.0
    A
    174.0 or more
    B
    Between 1 and 173.0
    C



B
Go to step 6

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.INSPECT MASS AIR FLOW METER (POWER SOURCE CIRCUIT)
  1. Disconnect the A4 mass air flow meter connector.



    A084809E16
  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector and the body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    +B (A4-1) - Body ground
    11 to 14 V



NG
Go to step 5
OK


3.INSPECT ECM (VG VOLTAGE)


    A154534E14
  1. Start the engine.

  1. Measure the voltage of the ECM connector.

    HINT:
    The A/C switch should be turned OFF.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    VG (E7-24) - EVG (E7-32)
    Engine is idling
    0.5 to 3.4 V



OK
REPLACE ECM (Click here)
NG


4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)


    A116703E08
  1. Disconnect the A4 mass air flow meter connector.

  1. Disconnect the E7 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    VG (A4-3) - VG (E7-24)
    Below 1 Ω
    E2G (A4-2) - EVG (E7-32)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    VG (A4-3) or VG (E7-24) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER (Click here)  

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - INTEGRATION RELAY)
G034942E04
  1. Disconnect the A4 MAF meter connector.

  1. Remove the integration relay from the engine room junction block (Click here).

  1. Disconnect the 1J integration relay connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    +B (A4-1) - 1J-5
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    +B (A4-1) or 1J-5 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)  

6.INSPECT ECM (SENSOR GROUND)


    A154534E15
  1. Measure the resistance of the ECM connector and body ground.

    Standard resistance:
    Tester Connection
    Specified Condition
    EVG (E7-32) - Body ground
    Below 1 Ω



NG
REPLACE ECM (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)


    A116703E09
  1. Disconnect the A4 mass air flow meter connector.

  1. Disconnect the E7 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    VG (A4-3) - VG (E7-24)
    Below 1 Ω
    E2G (A4-2) - EVG (E7-32)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    VG (A4-3) or VG (E7-24) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER (Click here)