DTC P0087 Fuel Rail / System Pressure - Too Low |
DTC P0190 Fuel Rail Pressure Sensor Circuit |
DTC P0192 Fuel Rail Pressure Sensor Circuit Low Input |
DTC P0193 Fuel Rail Pressure Sensor Circuit High Input |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0087 | Fuel pressure sensor output voltage stays at fixed value (1 trip detection logic) |
|
| P0190 | Fuel pressure sensor output voltage is 0.55 V or less, or 4.9 V or more for 0.5 seconds (1 trip detection logic) |
|
| P0192 | Fuel pressure sensor output voltage is 0.55 V or less for 0.5 seconds (1 trip detection logic) |
|
| P0193 | Fuel pressure sensor output voltage is 4.9 V or more for 0.5 seconds (1 trip detection logic) |
|
| Engine Speed | Fuel Pressure |
| Idling | Approximately 30 to 40 MPa |
| 3,000 rpm (No engine load) | Approximately 45 to 75 MPa |

| Required Sensors | Fuel pressure sensor |
| Frequency of operation | Continuous |
| Duration | 1 second |
| MIL operation | 1 driving cycle |
| Required Sensors | Fuel pressure sensor |
| Frequency of operation | Continuous |
| Duration | 0.5 seconds |
| MIL operation | 1 driving cycle |
| Required Sensors | Fuel pressure sensor |
| Frequency of operation | Continuous |
| Duration | 0.5 seconds |
| MIL operation | 1 driving cycle |
| Required Sensors | Fuel pressure sensor |
| Frequency of operation | Continuous |
| Duration | 0.5 seconds |
| MIL operation | 1 driving cycle |
| Item | Specification | Specification |
| Minimum | Maximum | |
| Engine speed | 500 rpm | - |
| Battery voltage | 8 V | - |
| Fuel volume | 5 mm3
| - |
| The monitor will not run if the fuel pressure sensor circuit (P0190, P0192 and P0193) is malfunctioning. | ||
| Detection Criteria | Threshold |
| Changing value of fuel pressure | Virtually no fluctuation |
| Detection Criteria | Threshold |
| Fuel pressure sensor output voltage | Less than 0.55 V or more than 4.9 V |
| Detection Criteria | Threshold |
| Fuel pressure sensor output voltage | Less than 0.55 V |
| Detection Criteria | Threshold |
| Fuel pressure sensor output voltage | More than 4.9 V |

| 1.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine / Data List / Fuel Press.
Read the values.
| Engine Speed | Fuel Pressure |
| Idling | Approximately 30 to 40 MPa |
| 3,000 rpm (No engine load) | Approximately 45 to 75 MPa |
|
| ||||
| OK | |
| 2.CHECK IF DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine / DTC.
Clear the DTC(s).
Let the engine idle for 60 seconds, and then repeat quick engine RPM accelerations (to 2,500 rpm) for 30 seconds.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTC(s).
| Display (DTC Output) | Proceed to |
| P0087, P0190, P0192 and/or P0193 | A |
| No output | B |
|
| ||||
| A | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM) |
![]() |
Disconnect the E7 and E8 ECM connector.
Disconnect the F9 fuel pressure sensor connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| PCR1 (E8-26) - PR (F9-5) | Below 1 Ω |
| PCR2 (E8-33) - PR2 (F9-2) | Below 1 Ω |
| VCS (E7-2) - VCS (F9-1) | Below 1 Ω |
| VC (E8-18) - VC (F9-6) | Below 1 Ω |
| E2 (E8-28) - E2 (F9-4) | Below 1 Ω |
| E2S (E7-1) - E2S (F9-3) | Below 1 Ω |
| Tester Connection | Specified Condition |
| PCR1 (E8-26) or PR (F9-5) - Body ground | 10 kΩ or higher |
| PCR2 (E8-33) or PR2 (F9-2) - Body ground | 10 kΩ or higher |
| VCS (E7-2) or VCS (F9-1) - Body ground | 10 kΩ or higher |
| VC (E8-18) or VC (F9-6) - Body ground | 10 kΩ or higher |
| E2 (E8-28) or E2 (F9-4) - Body ground | 10 kΩ or higher |
| E2S (E7-1) or E2S (F9-3) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||