DTC P0200 Injector Circuit / Open |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0200 |
(1 trip detection logic) |
|


| Malfunction Point | Trouble Area |
| A |
|
| B (If A is normal) |
|
| C (If A and B are normal) |
|
| D (If A, B and C are normal) |
|
![]() |
| Inspection Point | Specified Condition |
| A and B | Correct waveform is as shown |
![]() |
| Inspection Point | Specified Condition |
| C and D | Correct waveform is as shown |
| Required sensor | INJF signal from EDU |
| Frequency of operation | Continuous |
| Duration | 10 seconds |
| MIL operation | 1 driving cycle |
| Item | Specification | |
| Minimum | Maximum | |
| Engine speed | 500 rpm | - |
| Battery voltage | 11 V | - |
| Ignition switch | ON | ON |
| Threshold |
| Injection missing counter* for all cylinders, or for one individual cylinder, reaches specified number (taking approximately 1 second from starting engine) *: Increases when no IJF signal is received from the EDU despite the ECM sending the IJT signals. |


| 1.INSPECT INJECTOR ASSEMBLY |
![]() |
Disconnect the F5, F6, F7 and F8 injector connectors.
Measure the resistance of the injection assembly.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 0.42 to 0.52 Ω |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER [EDU] - INJECTOR ASSEMBLY) |
Check the harness and connector between the injector and EDU (INJ terminal).
![]() |
Disconnect the F5, F6, F7 and/or F8 injector connectors.
Disconnect the I17 and/or I18 EDU connectors.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| F5-1 - IJ1+ (I17-1) | Below 1 Ω |
| F6-1 - IJ2+ (I17-6) | |
| F7-1 - IJ3+ (I17-5) | |
| F8-1 - IJ4+ (I18-3) | |
| F5-2 - IJ1- (I18-6) | |
| F6-2 - IJ2- (I18-4) | |
| F7-2 - IJ3- (I18-2) | |
| F8-2 - IJ4- (I18-5) |
| Tester Connection | Specified Condition |
| F5-1 or IJ1+ (I17-1) - Body ground | 10 kΩ or higher |
| F6-1 or IJ2+ (I17-6) - Body ground | |
| F7-1 or IJ3+ (I17-5) - Body ground | |
| F8-1 or IJ4+ (I18-3) - Body ground | |
| F5-2 or IJ1- (I18-6) - Body ground | |
| F6-2 or IJ2- (I18-4) - Body ground | |
| F7-2 or IJ3- (I18-2) - Body ground | |
| F8-2 or IJ4- (I18-5) - Body ground |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER [EDU] - ECM) |
![]() |
Disconnect the I19 EDU connector.
Disconnect the E8 ECM connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| #10 (I19-4) - #1 (E8-24) | Below 1 Ω |
| #20 (I19-8) - #2 (E8-23) | |
| #30 (I19-7) - #3 (E8-22) | |
| #40 (I19-3) - #4 (E8-21) | |
| IJNF (I19-5) - INJF (E8-25) |
| Tester Connection | Specified Condition |
| #10 (I19-4) or #1 (E8-24) - Body ground | 10 kΩ or higher |
| #20 (I19-8) or #2 (E8-23) - Body ground | |
| #30 (I19-7) or #3 (E8-22) - Body ground | |
| #40 (I19-3) or #4 (E8-21) - Body ground | |
| IJNF (I19-5) or INJF (E8-25) - Body ground |
|
| ||||
| OK | |
| 4.INSPECT INJECTOR DRIVER (EDU) (BATTERY VOLTAGE) |
![]() |
Disconnect the I17 EDU connector.
Turn the ignition switch ON.
Measure the voltage of the EDU connector.
| Tester Connection | Specified Condition |
| +B (I17-2) - GND (I17-3) | 11 to 14 V |
|
| ||||
| OK | |
| 5.REPLACE INJECTOR DRIVER (EDU) |
Replace injector driver (Click here).
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the tester ON.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 30 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0200 | B |
|
| ||||
| A | ||
| ||