Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    41    Air Mix Damper Control Servo Motor Circuit (Passenger Side)

for Preparation Click here


DESCRIPTION

The air mix setting is controlled as follows:
The air mix damper servo (air mix damper servo motor) sends the air mix damper position as a pulse signal to the air conditioning amplifier. Then the air conditioning amplifier uses the pulse to determine how much the servo motor should be rotated forward/backward, and moves the air mix damper to the appropriate position.

HINT:
This DTC is also output if the damper and damper link are malfunctioning or unable to move properly. When this DTC is output, confirm that the mechanical parts of the damper and damper link are not defective or damaged.


DTC Code
Detection Item
Trouble Area
41
Air mix damper control servo motor activation request signal is output, but servo motor position data does not change or is inaccurate
  1. Air mix damper servo sub-assembly (Air mix damper servo motor)
  2. Harness or connector
  3. Air conditioning amplifier assembly

WIRING DIAGRAM


E171021E01


INSPECTION PROCEDURE

1.PERFORM ACTUATOR CHECK
  1. Warm up the engine.

  1. Enter actuator check mode (Click here).

  1. Press the DEF switch to change to the step operation (Click here).

  1. Press the DEF switch to check the air flow by hand.
    Display Code
    Air Mix Damper Position
    0
    COOL side (0% open)
    1
    COOL side (0% open)
    2
    COOL side (0% open)
    3
    COOL side (0% open)
    4
    COOL/HOT (50% open)
    5
    COOL/HOT (50% open)
    6
    HOT side (100% open)
    7
    HOT side (100% open)
    8
    HOT side (100% open)
    9
    HOT side (100% open)

    OK:
    Air mix damper position changes in accordance with each display code.

    Result 
    Result
    Proceed to
    OK (Checking from the PROBLEM SYMPTOMS TABLE)
    A
    OK (Checking from the DTC)
    B
    NG
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
Go to step 2
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK HARNESS AND CONNECTOR (AIR MIX DAMPER SERVO - AIR CONDITIONING AMPLIFIER)


    E170956E07
  1. Disconnect the D17 servo connector.

  1. Disconnect the A37 and A38 amplifier connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D17-5 (MHD) - A37-17 (AMH)
    Always
    Below 1 Ω
    D17-4 (MCD) - A37-19 (AMC)
    D17-3 (MHP) - A38-23 (PMB)
    D17-2 (MCP) - A38-24 (PMA)
    D17-1 (SG) - A38-20 (SG-1)
    D17-1 (SG) - Body ground
    Always
    10 kΩ or higher
    D17-2 (MCP) - Body ground
    D17-3 (MHP) - Body ground
    D17-4 (MCD) - Body ground
    D17-5 (MHD) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK AIR MIX DAMPER SERVO SUB-ASSEMBLY (AIR MIX DAMPER SERVO MOTOR)
  1. Check if the malfunction disappears when a normally functioning air mix damper servo (air mix damper servo motor) is installed.

    OK:
    Air mix control damper operates normally.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

REPLACE AIR MIX DAMPER SERVO SUB-ASSEMBLY (AIR MIX DAMPER SERVO MOTOR) (Click here)