COMMON RAIL (w/ EGR Cooler) > INSTALLATION |
| 1. INSTALL COMMON RAIL ASSEMBLY |
![]() |
Install the common rail and insulator with the 2 bolts.
Connect the 2 connectors.
| 2. INSTALL FUEL INLET PIPE SUB-ASSEMBLY |
![]() |
Temporarily install the fuel inlet pipe with the union nuts.
Install a new O-ring to the oil level gauge guide, and install the oil level gauge guide to the cylinder block.
![]() |
Temporarily install the stay of the oil level gauge guide to the intake manifold with the bolt.
![]() |
Install the clamp with the bolt.
Tighten the bolt of the oil level gauge guide stay.
![]() |
Using a 17 mm union nut wrench, tighten the injection pipe union nut on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nut on the supply pump side.
| 3. INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY |
![]() |
Temporarily install the leakage pipe with the 3 bolts.
Temporarily install a new gasket with the check valve.
Tighten the 3 bolts and check valve.
Connect the 3 fuel hoses.
| 4. INSTALL NO. 4 INJECTION PIPE |
![]() |
Temporarily install the No. 4 injection pipe with the union nuts.
Install new injection pipe clamp with the bolt.
![]() |
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.
Using a union nut wrench, tighten the injection pipe union nuts on the injector side.
| 5. INSTALL EGR COOLER ASSEMBLY |
Install the EGR cooler assembly (Click here).
| 6. INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE |
Temporarily install the No. 1, No. 2 and No. 3 injection pipes with the union nuts.
![]() |
Install the No. 2 and No. 3 injection pipe clamps with the 2 bolts and 2 nuts, as shown in the illustration.
![]() |
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
| 7. INSTALL OIL FILTER SUB-ASSEMBLY |
Check and clean the oil filter installation surface.
Apply clean engine oil to the gasket of a new oil filter.
Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.
![]() |
Using SST, tighten the oil filter. Depending on the work space available, choose from the following.
If enough space is available, use a torque wrench to tighten the oil filter.
If enough space is not available to use a torque wrench, tighten the oil filter 3/4 turn by hand or with a common wrench.
| 8. INSTALL MANIFOLD STAY |
![]() |
Install the stay with the 2 bolts.
Connect the 3 vacuum hoses to the 2 VSV.
| 9. INSTALL INTERCOOLER ASSEMBLY |
Install the intercooler assembly (Click here).
| 10. ADD FUEL |
| 11. TIGHTEN FUEL TANK CAP ASSEMBLY |
| 12. ADD ENGINE OIL |
| 13. BLEED AIR FROM FUEL SYSTEM |
| 14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 15. PERFORM INITIALIZATION |
Perform initialization (Click here).
| 16. CHECK ENGINE OIL LEAKS |
| 17. CHECK FUEL LEAKS |
| 18. INSTALL NO. 2 ENGINE UNDER COVER |
Install the under cover with the 4 bolts.
| 19. INSTALL NO. 1 ENGINE UNDER COVER |
Install the under cover with the 4 bolts.