Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM (w/ VSC)

CAN COMMUNICATION SYSTEM (w/ VSC) > Open in CAN Main Bus Line


DESCRIPTION

There may be an open circuit in the CAN main wire and/or the DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher.
  1. CAN main wire and connector
  2. No. 1 junction connector
  3. No. 2 junction connector
  4. No. 3 junction connector
  5. ECM
  6. DLC3 branch wire or connector

WIRING DIAGRAM


C190674E03


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2.CHECK DLC3


    H102621E27
  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    D1-6 (CANH) - D1-14 (CANL)
    Ignition switch off
    54 to 69 Ω
    OK
    70 Ω or higher
    NG

    NOTICE:
    When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a problem besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "How to Proceed with Troubleshooting" (Click here) after repairing the trouble area.



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)


    C190785E05
  1. Disconnect the J54 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J54-4 (CANH) - J54-1 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 5
OK


4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - ECM)


    C190785E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J54-12 (CANH) - J54-6 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 10
OK

REPLACE NO. 1 JUNCTION CONNECTOR 

5.CONNECT CONNECTOR
  1. Reconnect the J54 No. 1 junction connector connector.


NEXT


6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)


    C190786E05
  1. Disconnect the J53 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J53-3 (CANH) - J53-7 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 8
OK


7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C190786E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J53-1 (CANH) - J53-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 2 JUNCTION CONNECTOR 

8.CONNECT CONNECTOR
  1. Reconnect the J53 No. 2 junction connector connector.


NEXT


9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C190789E05
  1. Disconnect the J50 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J50-2 (CANH) - J50-1 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 3 JUNCTION CONNECTOR 

10.CONNECT CONNECTOR
  1. Reconnect the J54 No. 1 junction connector connector.


NEXT


11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 1 JUNCTION CONNECTOR)


    C190783E03
  1. Disconnect the E6 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E6-24 (CANH) - E6-23 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 1 JUNCTION CONNECTOR)
OK

REPLACE ECM (Click here)