Home › SECURITIES › ENGINE IMMOBILISER › TRANSPONDER KEY AMPLIFIER

TRANSPONDER KEY AMPLIFIER > INSTALLATION

for Preparation Click here



1. INSTALL TRANSPONDER KEY AMPLIFIER


    G034429E03
  1. Align the claw of the amplifier with the upper bracket.

  1. Push in the amplifier and install it to the upper bracket.

    NOTICE:
    Do not push in the amplifier with excessive force as it may be damaged.

  1. Connect the amplifier connector.



2. INSTALL UPPER STEERING COLUMN COVER


G034336E01
  1. Install the cover lower with the 3 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



3. INSTALL LOWER STEERING COLUMN COVER


G034336E01
  1. Install the cover lower with the 3 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



4. INSTALL STEERING WHEEL ASSEMBLY (w/ Airbag System, w/ Steering Pad Switch)


    G039075E03
  1. Align the matchmarks on the steering wheel and main shaft.

  1. Install the steering wheel with the set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



    B206142
  1. Connect the steering pad switch connector.



5. INSTALL STEERING WHEEL ASSEMBLY (w/ Airbag System, w/o Steering Pad Switch)


G039075E03
  1. Align the matchmarks on the steering wheel and main shaft.

  1. Install the steering set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



6. INSTALL STEERING WHEEL ASSEMBLY (w/o Airbag System, w/o Steering Pad Switch)


G039075E03
  1. Align the matchmarks on the steering wheel and main shaft.

  1. Install the steering set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



7. INSTALL STEERING PAD ASSEMBLY (w/ Airbag System, w/ Steering Pad Switch)


B085363E01
  1. Support the steering pad with one hand as shown in the illustration.

  1. Connect the airbag connector.

    NOTICE:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. Connect the horn connector.

  1. Install the steering pad after confirming that the circumference grooves of the screws are caught on the screw case.

  1. Using a T30 "torx" socket, install the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



8. INSTALL STEERING PAD ASSEMBLY (w/ Airbag System, w/o Steering Pad Switch)


B085363E01
  1. Support the steering pad with one hand as shown in the illustration.

  1. Connect the airbag connector.

    NOTICE:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. Connect the horn connector.

  1. Install the steering pad after confirming that the circumference grooves of the screws are caught on the screw case.

  1. Using a T30 "torx" socket, install the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



9. INSTALL STEERING PAD ASSEMBLY (w/o Airbag System, w/o Steering Pad Switch)


  1. for Type A:



      B207734
    1. Attach the 4 claws shown in the illustration to the steering wheel to install the steering pad.



  1. for Type B:

    1. Connect the horn connector.



    2. C194098
    3. Attach the 3 clips shown in the illustration to the steering wheel to install the steering pad.



    4. C194096
    5. Install the screw.



10. INSTALL LOWER NO. 3 STEERING WHEEL COVER (w/ Airbag System, w/ Steering Pad Switch)


    B176819
  1. Attach the 2 claws to install the cover.



11. INSTALL LOWER NO. 2 STEERING WHEEL COVER (w/ Airbag System, w/ Steering Pad Switch)


    B176820
  1. Attach the 2 claws to install the cover.



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



13. CHECK SRS WARNING LIGHT
  1. For vehicles with SRS:
    Check the SRS warning light (Click here).



14. CHECK ENGINE START
  1. Start the engine. Then check that the engine idles.