Home › BODY › SEAT › FRONT POWER SEAT MOTOR ASSEMBLY (for Reclining)

FRONT POWER SEAT MOTOR ASSEMBLY (for Reclining) > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

NOTICE:
If the rear power seat motor has been dropped, replace it with a new one.



1. INSTALL FRONT POWER SEAT MOTOR ASSEMBLY (for Reclining)


    B206608
  1. Temporarily install the power seat motor with the 3 bolts.



    B206609
  1. Install the reclining rod.



    B207099
  1. Attach the 6 claws to install the push nut to the reclining rod.

  1. Using a 4 mm socket hexagon wrench, tighten the 3 bolts.

    Torque:
    4.5 N*m{ 46 kgf*cm , 40 in.*lbf }



    B207267
  1. Attach the 8 hooks to install the seatback spring.

  1. Connect the connector.



2. INSTALL RECLINING ADJUSTER INSIDE COVER RH


    B171585E02
  1. Attach the guide to install the reclining adjuster inside cover.

  1. Install the screw.



3. INSTALL RECLINING ADJUSTER INSIDE COVER RH


    B207093
  1. Attach the claw to install the reclining adjuster inside cover.

  1. Install the screw.



4. INSTALL NO. 1 SEATBACK CLOTH


    B207461
  1. Install the seatback cloth.



5. INSTALL SEPARATE TYPE FRONT SEATBACK PAD


    B207459
  1. Install the seatback pad.



6. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    B207460E01
  1. Using hog ring pliers, attach the strap of the seatback cover to the seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B207457
  1. Attach the 4 claws to install the 2 headrest supports.



    B207582E01
  1. Using hog ring pliers, install the upper part of the seatback cover to the seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B257947E01
  1. Using hog ring pliers, install the center of the seatback cover to the seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B207454E01
  1. Using hog ring pliers, attach the strap of the seatback cover to the seatback frame with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



    B207453E01
  1. Using hog ring pliers, attach the bottom of the seatback cloth to the seatback frame with new hog rings.



    B207452E01
  1. Using hog ring pliers, attach the wires at the bottom of the seatback cover with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



7. INSTALL FRONT SEAT CUSHION INNER SHIELD RH


  1. Pass the wire harness of the front seat inner belt assembly below the claw and into the front seat cushion inner shield.


    B207196



    B207618
  1. Attach the claw to temporarily install the cushion inner shield.

    NOTICE:
    Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat cushion inner shield.



    B207198
  1. Attach the guide and claw.

    NOTICE:
    Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat cushion inner shield.

  1. Install the screw to the cushion inner shield.



8. INSTALL FRONT SEAT CUSHION SHIELD RH


    B207039
  1. Attach the claw and guide to install the cushion shield.

  1. Install the 3 screws.



    B207078
  1. Install the 2 screws.



9. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    B207446
  1. Attach the 4 claws to install the knob.



10. INSTALL RECLINING POWER SEAT SWITCH KNOB


    B207447
  1. Attach the 2 claws to install the knob.



11. INSTALL FRONT SEAT ASSEMBLY
  1. Install the front seat assembly (Click here).



12. INSPECT FRONT SEAT ASSEMBLY
  1. Check the power seat operation (Click here).