ENGINE ASSEMBLY > INSTALLATION |
| 1. INSTALL WIRE HARNESS CLAMP BRACKET |
Install the wire harness clamp bracket with the bolt.
| 2. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY |
![]() |
Clean the threads of the oil pressure switch, and apply adhesive to them.
![]() |
Using a 24 mm deep socket wrench, install the oil pressure switch.
| 3. INSTALL EXHAUST MANIFOLD |
![]() |
Install a new gasket to the cylinder head.
![]() |
Install the exhaust manifold with the 6 bolts and 2 new nuts. Uniformly tighten the bolts and nuts in several steps.
| 4. INSTALL NO. 1 FRONT ENGINE MOUNTING BRACKET RH |
![]() |
Install the engine mounting bracket with the 4 bolts.
| 5. INSTALL PUMP BRACKET |
![]() |
Install the pump bracket with the 6 bolts.
| 6. INSTALL WATER BY-PASS HOSE UNION |
Clean the threads of the water by-pass hose union, and apply adhesive to them.
Install the water by-pass hose union.
| 7. INSTALL INTAKE MANIFOLD |
![]() |
Install a new gasket to the cylinder head with the protrusion facing upward.
![]() |
Install the intake manifold with the 6 bolts and 2 nuts. Uniformly tighten the bolts and nuts in several steps.
| 8. INSTALL WATER OUTLET HOUSING |
Install a new gasket to the cylinder head.
![]() |
Install the outlet hosing with the 3 bolts.
| 9. INSTALL ENGINE COOLANT TEMPERATURE SENSOR |
![]() |
Install a new gasket and the sensor with the bolt.
Connect the sensor connector.
| 10. INSTALL CRANKSHAFT POSITION SENSOR |
Apply a light coat of engine oil to the O-ring of the sensor.
![]() |
Install the sensor with the bolt.
Connect the sensor connector.
| 11. INSTALL INJECTION PUMP ASSEMBLY |
![]() |
Install the injection pump to the timing gear case, and temporarily tighten the 2 nuts.
Install the injection pump stay to the injection pump rear end, and temporarily tighten the 3 bolts.
![]() |
Rotate the pump body to align the markings of the pump flange and timing gear case.
Tighten the 2 nuts to install the injection pump.
Tighten the 3 bolts to install the injection pump stay.
![]() |
Connect the 3 fuel hoses.
Connect the engine speed sensor connector.
Connect the spill control valve connector.
Connect the correction unit connector.
Connect the timing control valve connector.
Connect the fuel temperature sensor connector.
Connect the engine wire clamp.
| 12. INSTALL INJECTION PUMP DRIVE PULLEY |
![]() |
Using SST, install the injection pump drive pulley with the nut.
| 13. INSTALL GLOW PLUG ASSEMBLY |
![]() |
Using a 12 mm deep socket wrench, install the 4 glow plugs.
| 14. INSTALL NOZZLE HOLDER & NOZZLE SET |
![]() |
Place 4 new injection nozzle seat gaskets and 4 injection nozzle seats into the injection nozzle holes of the cylinder head.
Using SST, install the 4 nozzle holders and nozzle sets.
| 15. INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY |
![]() |
Install 4 new ring packing washers and the leakage pipe with the 4 nuts.
Connect the fuel hose to the leakage pipe.
| 16. INSTALL NO. 1 GLOW PLUG CONNECTOR |
Install the glow plug connector by uniformly tightening the 4 nuts.
Install the 4 screw grommets.
Connect the glow plug connector wire with the nut.
| 17. INSTALL INJECTION PIPE SET |
![]() |
Connect the 2 lower pipe clamps onto the intake manifold.
Install the 4 injection pipes.
Secure the injection pipes with the 2 upper pipe clamps and 2 nuts.
| 18. INSTALL VENTURI ASSEMBLY |
Place a new gasket and the venturi on the intake manifold.
![]() |
Connect the throttle control motor connector.
![]() |
Connect the throttle open switch connector.
| 19. INSTALL OIL DIPSTICK GUIDE |
Apply clean engine oil to a new O-ring.
Install the O-ring to the guide.
Install the guide with the 2 bolts.
| 20. INSTALL OIL DIPSTICK SUB-ASSEMBLY |
Install the dipstick to the guide.
| 21. INSTALL INTAKE PIPE |
![]() |
Install the intake pipe with the 2 bolts.
Tighten the intake pipe clamp.
| 22. INSTALL GENERATOR ASSEMBLY |
![]() |
Install the generator with the bolt.
Connect the vacuum oil outlet hose.
![]() |
Install 2 new gaskets and the vacuum pump hose with the union bolt.
Install the vacuum pump oil inlet hose with 2 new gaskets and the union bolt.
Attach the vacuum pump oil inlet hose to the cord clip.
![]() |
Install the generator wire with the nut.
Attach the terminal cap.
Connect the generator connector.
| 23. INSTALL COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System) |
Temporarily install the compressor mounting bracket with the 4 bolts.
![]() |
Using several steps, uniformly install and tighten the 4 bolts.
![]() |
Temporarily install the spacer with the bolt.
| 24. INSTALL FAN BELT ADJUSTING BAR (w/o Air Conditioning System) |
![]() |
Install the fan belt adjusting bar with the 2 bolts.
![]() |
Temporarily install the bolt.
| 25. INSTALL ENGINE WIRE |
| 26. REMOVE ENGINE ON ENGINE STAND |
| 27. INSTALL ENGINE ASSEMBLY |
Attach a chain block and engine sling device to the engine hangers.
Slowly lower the engine into the engine compartment.
Install the engine mounting bracket with the 4 bolts.
Remove the bolt and No. 2 engine hanger.
| 28. INSTALL VANE PUMP ASSEMBLY |
Temporarily install the vane pump assembly with the 2 bolts.
![]() |
Install the pulley to the pump shaft.
Using SST, stop the pulley rotation and torque the nut.
| 29. INSTALL COMPRESSOR AND MAGNET CLUTCH (w/ Air Conditioning System) |
![]() |
Install the compressor with the 4 bolts.
| 30. CONNECT HOSES AND CONNECTORS |
Connect the vacuum pump hose to the generator.
![]() |
Connect the connectors as shown in the illustration.
![]() |
Connect the compressor connector.
![]() |
Connect the 2 water hoses.
Install the water hose clamp with the bolt.
![]() |
Connect the 2 fuel hoses.
![]() |
Install the ground cable with the bolt.
Connect the 2 engine room junction block connectors.
Install the engine room junction block wire with the nut.
Install the engine room relay block cover (side).
Install the engine room relay block cover (upper).
| 31. INSTALL REAR END PLATE |
Install the rear end plate with the 2 bolts.
| 32. INSTALL FLYWHEEL SUB-ASSEMBLY |
![]() |
Using SST, hold the crankshaft.
Clean the bolts and bolt holes.
![]() |
Apply adhesive to 2 or 3 threads of the bolts.
Install the flywheel on the crankshaft.
![]() |
Install and uniformly tighten the 8 bolts in several steps, in the sequence shown in the illustration.
| 33. INSTALL CLUTCH DISC ASSEMBLY |
![]() |
Insert SST into the clutch disc. Then insert the SST (together with the clutch disc) into the flywheel.
| 34. INSTALL CLUTCH COVER ASSEMBLY |
![]() |
Align the matchmarks on the clutch cover and flywheel.
Tighten the 6 bolts as described below.
Determine the first bolt to be tightened by choosing the bolt closest to the knock pin.
Uniformly tighten the 6 bolts in diametrically opposite pairs relative to the position of the first bolt. Use the illustration as a reference.
Lightly move SST up and down, and right and left.
Check that the disc is in the center, and then tighten the bolts.
| 35. INSTALL TRANSMISSION ASSEMBLY |
![]() |
Align the input shaft with the clutch disc and install the transmission to the engine.
Install the 4 bolts.
| 36. INSTALL PROPELLER SHAFT ASSEMBLY |
for Front Side:
Install the propeller shaft (Click here).
for Rear Side:
Install the propeller shaft (Click here).
| 37. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
Install a new gasket to the front exhaust pipe.
Temporarily install the pipe support and clamp to the front exhaust pipe with the bolt.
Install the front exhaust pipe to the exhaust manifold with 3 new nuts. Alternately tighten the nuts in several passes.
Install the pipe support to the transmission with the 2 bolts.
Tighten the pipe support's clamp with the bolt.
Install the front fender seal LH with the 5 clips.
| 38. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Install the heat insulator with the 3 bolts.
| 39. INSTALL STARTER ASSEMBLY |
![]() |
Install the starter with the 2 bolts and nut.
Install the stay with the 2 bolts.
Install the nut to the stay.
Connect the terminal 30 wire with the nut.
![]() |
Install the terminal cap.
Connect the starter connector.
| 40. INSTALL RADIATOR ASSEMBLY |
![]() |
Install the radiator with the 4 bolts.
| 41. INSTALL FAN & GENERATOR V BELT (w/ Air Conditioning System) |
![]() |
Install the V belt.
Tightening bolt C, adjust the deflection of the V belt .
Tighten the bolts A and B.
Recheck the deflection of the V belt.
| 42. INSTALL FAN & GENERATOR V BELT (w/o Air Conditioning System) |
![]() |
Install the V belt.
Using a bar, adjust the tension of the V belt.
Tighten the bolts A and B.
Check the deflection of the V belt .
| 43. INSTALL COOLER COMPRESSOR V BELT (w/ Air Conditioning System) |
![]() |
Install the V belt.
Tightening bolt B, adjust the deflection of the V belt .
Tighten nut A.
Recheck the deflection of the V belt.
| 44. INSTALL VANE PUMP V BELT |
![]() |
Install the V belt.
Using a bar, adjust the deflection of the V belt .
Tighten bolt A and nut B.
Recheck the deflection of the V belt.
| 45. INSTALL FAN SHROUD |
![]() |
Install the fan pulley to the water pump.
Install the shroud together with the coupling fan between the radiator and engine.
Install the fluid coupling fan to the fan pulley with the 4 nuts.
Attach the shroud's claws to the radiator as shown in A in the illustration.
Install the shroud with the 2 bolts.
Install the fan and generator V belt, cooler compressor V belt and vane pump V belt (Click here).
Tighten the 4 nuts of the fluid coupling fan.
![]() |
Install the radiator reservoir with the bolt.
Connect the No. 1 and No. 2 water by-pass hoses to the tank upper and lower.
![]() |
Install the oil reservoir with the 3 bolts.
| 46. CONNECT RADIATOR HOSE OUTLET |
| 47. CONNECT RADIATOR HOSE INLET |
| 48. INSTALL AIR CLEANER ASSEMBLY |
Install the cleaner with the 2 bolts.
Connect the connector to the IAT sensor.
Connect the hose clamp.
| 49. INSTALL BATTERY AND BATTERY TRAY |
| 50. INSTALL BATTERY BRACKET |
Install the battery bracket with the bolt.
| 51. INSTALL HOOD SUB-ASSEMBLY |
Install the hood with the 4 bolts.
Connect the washer nozzle hose.
Adjust the hood.
| 52. ADD ENGINE OIL |
Add fresh engine oil.
| Item | Specified Condition |
| Drain and refill with oil filter change | 7.2 liters (7.6 US qts, 6.3 Imp. qts) |
| Drain and refill without oil filter change | 6.7 liters (7.1 US qts, 5.9 Imp. qts) |
| Dry fill | 8.4 liters (8.9 US qts, 7.4 Imp. qts) |
Install the oil filler cap.
| 53. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
![]() |
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's FULL line.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the LOW line, add TOYOTA SLLC to the FULL line.
Install the radiator reservoir cap.
![]() |
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2,500 to 3,000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
After the coolant cools down, check that the coolant level is at the FULL line.
If the coolant level is below the LOW line, add TOYOTA SLLC to the FULL line.
| 54. TIGHTEN FUEL TANK CAP ASSEMBLY |
| 55. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump, bleed air from the fuel system until pumping becomes difficult.
| 56. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 57. INSPECT FOR FUEL LEAK |
Check that there are no fuel leaks anywhere on the fuel system after performing maintenance.
| 58. INSPECT FOR OIL LEAK |
Start the engine, and check that there are no oil leaks after performing maintenance.
| 59. INSPECT FOR COOLANT LEAK |
Check for engine coolant leaks .
| 60. INSPECT FOR EXHAUST GAS LEAK |
| 61. INSPECT ENGINE IDLE SPEED |
Warm up the engine.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Measure the idle speed.
When not using the intelligent tester:
![]() |
Using SST, connect the tachometer test probe to terminal 9 (TAC) of the DLC3.
Measure the idle speed.
| 62. INSPECT MAXIMUM ENGINE SPEED |
Start the engine.
Fully depress the accelerator pedal.
Measure the maximum speed.
| 63. INSTALL NO. 2 ENGINE UNDER COVER |
Install the under cover with the 4 bolts.
| 64. INSTALL NO. 1 ENGINE UNDER COVER |
Install the under cover with the 8 bolts.