UPPER INSTRUMENT PANEL > REMOVAL |
| 1. TABLE OF BOLT, SCREW AND NUT |
![]() |
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabetical code in the table.
| 2. PRECAUTION |
| 3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 4. REMOVE STEERING WHEEL ASSEMBLY |
| 5. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL |
![]() |
Remove the clip <C>.
Detach the 2 claws and 3 guides and remove the No. 1 instrument cluster finish panel.
| 6. REMOVE COMBINATION METER ASSEMBLY |
![]() |
Remove the 3 screws.
Disconnect the connectors, detach the clamp and remove the combination meter.
| 7. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
![]() |
for Manual Air Conditioning System:
Put protective tape around the center instrument cluster finish panel.
| *1 | Protective Tape |
Using a moulding remover, detach the 10 claws and 4 clips.
![]() |
Detach the 4 claws and disconnect the air conditioner control.
Disconnect the connectors and remove the center instrument cluster finish panel.
![]() |
for Automatic Air Conditioning System:
Put protective tape around the center instrument cluster finish panel.
| *1 | Protective Tape |
Using a moulding remover, detach the 8 claws and 4 clips.
Disconnect the connectors and remove the center instrument cluster finish panel.
| 8. REMOVE RADIO RECEIVER ASSEMBLY (w/ Audio) |
for Radio Receiver Type:
for Radio and Display Type:
| 9. REMOVE RADIO TUNER OPENING COVER (w/o Audio) |
![]() |
Remove the 4 screws and radio tuner opening cover.
| 10. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Slightly bend the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.
| *1 | Stopper |
![]() |
Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.
| *1 | Hinge |
| 11. REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY |
![]() |
Disconnect the connector from the airbag.
![]() |
Remove the 2 bolts.
Detach the clamp from the bracket.
![]() |
Detach the 12 claws and remove the airbag.
| 12. REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH |
![]() |
Using a screwdriver, detach the 2 claws and remove the assist grip plug.
| *1 | Protective Tape |
| 13. REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH |
| 14. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY |
![]() |
Remove the 2 screws and front assist grip.
| 15. REMOVE FRONT PILLAR GARNISH LH |
![]() |
Remove the part of the front door opening trim attached to the front pillar garnish.
Detach the 2 clips and 2 guides and remove the front pillar garnish.
![]() |
w/ Curtain Shield Airbag:
Protect the curtain shield airbag assembly.
Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.
| *1 | Protective Cover |
| *2 | Adhesive Tape |
| 16. REMOVE FRONT PILLAR GARNISH RH |
| 17. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY |
for LHD:
Put protective tape around the upper instrument panel.
Remove the 2 bolts <A> and 2 screws <B>.
Using a screwdriver, detach the 8 claws and 5 guides and remove the upper instrument panel.

| *1 | Protective Tape | *2 | Bolt <A> |
| *3 | Screw <B> | - | - |
for RHD:
Put protective tape around the upper instrument panel.
Remove the 2 bolts <A> and 2 screws <B>.
Using a screwdriver, detach the 8 claws and 5 guides and remove the upper instrument panel.

| *1 | Protective Tape | *2 | Bolt <A> |
| *3 | Screw <B> | - | - |
| 18. REMOVE GLOVE COMPARTMENT DOOR LOCK ASSEMBLY |
![]() |
Remove the 2 screws and glove compartment door lock.