DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) |
DTC P0156 Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2) |
DTC P0157 Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2) |
DTC P0158 Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 P0156 | During active control, heated oxygen sensor output voltage is 0.2 to 0.6 V |
|
| P0136 P0156 | (a) and (b) are met for more than 90 seconds (a) Estimated rear oxygen sensor temperature is less than 800°C (1,472°F) (b) Rear oxygen sensor impedance is less than 5 Ω | |
| P0137 P0157 | During active control, heated oxygen sensor output voltage is less than 0.2 V | |
| P0137 P0157 | (a) and (b) are met for more than 90 seconds (a) Estimated rear oxygen sensor temperature is less than 450°C (842°F) (b) Rear oxygen sensor impedance is more than 15 kΩ | |
| P0138 P0158 | During active control, heated oxygen sensor output voltage is more than 0.6 V | |
| P0138 P0158 | Rear oxygen sensor output voltage is 1.2 V or higher for more than 30 seconds |


| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS B1S1 or AFS B2S1 (A/F) | +25% | Rich | Less than 3.0 V |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5% | Lean | More than 3.35 V |
| O2S B1S1 or O2S B2S2 (heated oxygen sensor) | +25% | Rich | More than 0.55 V |
| O2S B1S1 or O2S B2S2 (heated oxygen sensor) | -12.5% | Lean | Less than 0.4 V |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.CHECK OTHER DTC OUTPUT (BESIDES DTC P0136, P0137, P0138, P0156, P0157 AND/OR P0158) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC output) | Proceed to |
| Only P0136, P0137, P0138, P0156, P0157 and/or P0158 are output | A |
| P0136, P0137, P0138, P0156, P0157 and/or P0158 and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
After warming up the engine, race the engine at 2,500 rpm for 3 minutes.
Read the output voltage of the heated oxygen sensor when the engine is suddenly raced.
|
| ||||
| NG | |
| 3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the H12 and H13 heated oxygen sensor connectors.
Measure the resistance of the sensor.
| Tester Connection | Condition | Specified Condition |
| 1 (HT1B) - 2 (+B) | 20°C (68°F) | 11 to 16 Ω |
| 1 (HT1B) - 4 (E2) | - | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 1 (HT2B) - 2 (+B) | 20°C (68°F) | 11 to 16 Ω |
| 1 (HT2B) - 4 (E2) | - | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT INTEGRATION NO.1 RELAY (MAIN RELAY) |
![]() |
Disconnect the integration relay from the engine room junction block.
Measure the voltage of the MAIN relay.
| Tester Connection | Condition | Specified Condition |
| 1J-5 - Body ground | Ignition switch ON | 10 to 14 V |
|
| ||||
| OK | |
| 5.CHECK WIRE HARNESS (HEATED OXYGEN SENSOR - ECM) |
![]() |
Disconnect the H12 and H13 connectors.
Disconnect the E15 and E16 ECM connectors.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| H12-1 (HT1B) - E15-1 (HT1B) | Below 1 Ω |
| H12-3 (OX1B) - E15-18 (OX1B) | Below 1 Ω |
| H12-1 (HT1B) or E15-1 (HT1B) - Body ground | 10 kΩ or higher |
| H12-3 (OX1B) or E15-18 (OX1B) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| BH13-1 (HT2B) - E16-5 (HT2B) | Below 1 Ω |
| H13-3 (OX2B) - E16-33 (OX2B) | Below 1 Ω |
| H13-1 (HT2B) or E16-5 (HT2B) - Body ground | 10 kΩ or higher |
| H13-3 (OX2B) or E16-33 (OX2B) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 7.READ OUTPUT DTC (DTC P0136 AND/OR P0156 ARE OUTPUT AGAIN) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC output) | Proceed to |
| P0136 and/or P0156 are not output again | A |
| P0136 and/or P0156 are output again | B |
|
| ||||
| A | ||
| ||