Home › ENGINE ยท 2TR-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL FRONT ENGINE MOUNTING BRACKET LH


    A099872E01
  1. Install the mounting bracket with the 4 bolts.

    Torque:
    51 N*m{ 520 kgf*cm , 38 ft.*lbf }



2. INSTALL FRONT ENGINE MOUNTING BRACKET RH


    A099873E01
  1. Install the mounting bracket with the 4 bolts.

    Torque:
    51 N*m{ 520 kgf*cm , 38 ft.*lbf }



3. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE


A099883E01
  1. Apply a coat of engine oil to a new O-ring.

  1. Install a new O-ring to the oil control valve.

  1. Install the oil control valve with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL CRANKSHAFT POSITION SENSOR


    A099147E04
  1. Apply a light coat of engine oil to the O-ring of the sensor.

  1. Install the sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Install the connector to the connector bracket.

  1. Attach the harness clamp.

  1. Connect the sensor connector.



5. INSTALL CAMSHAFT POSITION SENSOR


    G035088E01
  1. Apply a coat of engine oil to a new O-ring.

  1. Install the O-ring to the sensor.

  1. Install the sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



6. INSTALL ENGINE COOLANT TEMPERATURE SENSOR
  1. Using a 19 mm deep socket wrench, install a new gasket and the sensor.



7. INSTALL KNOCK SENSOR


    A099415E01
  1. Install the sensor so that it is horizontal as shown in the illustration. Then install the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    HINT:
    It is acceptable for the sensor to be tilted +-10°.

  1. Connect the sensor connector.



8. INSTALL NO. 1 WATER BY-PASS PIPE


    G037195E01
  1. Install a new gasket and the water by-pass pipe with the 2 nuts.

    Torque:
    17.5 N*m{ 178 kgf*cm , 13 ft.*lbf }



9. INSTALL ENGINE OIL PRESSURE SWITCH


    G036762E02
  1. Apply adhesive to 2 or 3 threads of the oil pressure switch.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the oil pressure switch.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 1 hour after installation of the switch.

  1. Connect the oil pressure switch connector.

  1. Start the engine and check for engine oil leaks.



10. INSTALL NO. 1 IDLER PULLEY


    G035185E01
  1. Install the spacer, idler pulley and pulley plate with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



11. INSTALL THERMOSTAT


    A110369E02
  1. Install a new gasket to the thermostat.

    HINT:
    When installing the thermostat to the gasket, be careful not to deform the gasket. Make sure that the thermostat is properly installed into the groove of the gasket, as shown in the illustration.

  1. Insert the thermostat into the cylinder block with the jiggle valve facing straight upward.

    HINT:
    The jiggle valve may be set within 10° of either side of the prescribed position.



12. INSTALL WATER INLET


    A120284E01
  1. Install the inlet with the 2 nuts and bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    A099676E01
  1. Connect the connector.



13. INSTALL V-RIBBED BELT TENSIONER


    G035081E02
  1. Temporarily install the belt tensioner with the 3 bolts.

    HINT:
    Make sure the flanges of the bolts are contacting the tensioner surface.

  1. Install the tensioner by tightening the 3 bolts in the order shown in the illustration.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf } for bolt 1
    21 N*m{ 214 kgf*cm , 15 ft.*lbf } for bolt 2
    43 N*m{ 438 kgf*cm , 32 ft.*lbf } for bolt 3



14. INSTALL COMPRESSOR MOUNTING BRACKET

NOTICE:
Install the compressor mounting bracket exactly as described in the procedures below to properly secure and prevent damage to the drive belt.



    A330624
  1. Temporarily install the compressor mounting bracket with the 3 bolts.

    HINT:
    Temporarily install the compressor mounting bracket with the 3 bolts so that the bracket can be moved by hand.



  1. Push the compressor mounting bracket toward the cylinder block as shown in the illustration and tighten bolt B.


    A332516E01

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf } for bolt B

    HINT:
    Make sure there is no clearance between the cylinder block and compressor mounting bracket as shown in the illustration.



    A332517E01
  1. Uniformly tighten the 4 bolts in the order shown in the illustration.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf } for bolt A
    24.5 N*m{ 250 kgf*cm , 18 ft.*lbf } for bolt C



15. INSTALL IDLE PULLEY ASSEMBLY
  1. Temporarily install the idle pulley assembly with the bolt.

    NOTICE:
    Do not use any tools.

  1. Tighten the bolt.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }



16. INSTALL EXHAUST MANIFOLD


    A099195E01
  1. Install a new gasket and the exhaust manifold with the 6 nuts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



17. INSTALL EXHAUST MANIFOLD HEAT INSULATOR


    A099875E01
  1. Install the heat insulator with the 5 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



18. INSTALL INTAKE MANIFOLD


    G036020E01
  1. Install a new gasket and the intake manifold with the 5 bolts and 2 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect the crankshaft position sensor to the clamp.



19. INSTALL INJECTOR


  1. Install each of the 4 injectors as follows.



      A099091E01
    1. Install a new insulator to the injector.

    2. Apply a light coat of grease or gasoline to a new O-ring and install it to the injector.

    3. Apply a light coat of grease or gasoline on the place where the delivery pipe touches the O-ring.



    4. A087155E01
    5. To install the fuel injector into the fuel delivery pipe, push the fuel injector while twisting it right and left.

      NOTICE:
      1. Be careful not to twist the O-ring.
      2. After installing the fuel injector, check that it turns smoothly. If it does not, reinstall it with a new O-ring.

    6. Position the injector connector so that it faces downward.



20. INSTALL FUEL DELIVERY PIPE


    G036023E01
  1. Install the 4 spacers to the cylinder head.



    G036024E01
  1. Install the delivery pipe together with the 4 injectors and 2 spacers with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Connect the 4 injector connectors.



    G035144E01
  1. Connect the 4 clamps and wire harness to the delivery pipe.

  1. Connect the vacuum hose.



21. INSTALL THROTTLE BODY


    G036423E01
  1. Install a new gasket on the intake manifold.

    HINT:
    Align the protrusion of the gasket with the groove of the intake manifold.



    A086829E01
  1. Install the throttle body with the 2 bolts and 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 2 water by-pass hoses to the throttle body.

  1. Connector the throttle position sensor and control motor connector.



22. INSTALL ENGINE WIRE


    G038850E03
  1. Connect the wire harness (engine ground wire) to the engine rear side with the 2 bolts so that it is within the specified range shown in the illustration.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }

  1. Connect the oil pressure sensor connector.

  1. Connect the noise filter connector.

  1. Connect the camshaft position sensor connector.

  1. Connect the 4 injector connectors.

  1. Connect the crankshaft position sensor connector.

  1. Connect the oil control valve connector.

  1. for Unleaded Gasoline Specification Vehicle:
    Connect the purge VSV connector.

  1. Connect the throttle body connector.

  1. Connect the engine coolant temperature sensor connector.

  1. Connect the knock sensor connector.

  1. Connect the wire harness to the clamps.



23. INSTALL GENERATOR


    A099681E03
  1. Install the generator with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Install the generator wire with the bolt and nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Attach the terminal cap.

  1. Connect the connector.



24. INSTALL VENTILATION PIPE
  1. Install the ventilation pipe with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



25. INSTALL SPARK PLUG


26. INSTALL IGNITION COIL
  1. Install the 4 ignition coils with the 4 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 4 ignition coil connectors.



27. REMOVE ENGINE FROM ENGINE STAND


28. INSTALL ENGINE ASSEMBLY


    A117894E02
  1. Attach the engine sling device and chain block to the engine hangers.

  1. Slowly lower the engine assembly into the engine compartment.



    G037190E01
  1. Install the engine mounting brackets with the 4 bolts and 4 nuts.

    Torque:
    38 N*m{ 388 kgf*cm , 28 ft.*lbf }



29. INSTALL REAR END PLATE
  1. Install the end plate with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



30. INSTALL FLYWHEEL

HINT:

  1. A004869E02
    The mounting bolts are tightened in 2 progressive steps.
  2. If a mounting bolts is broken or deformed, replace it.

  1. Apply adhesive to 2 or 3 threads of the mounting bolt end.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the flywheel.



    A099210E02
  1. Fix the crankshaft in place with SST.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    G035062E02
  1. Install and uniformly tighten the 10 mounting bolts in several passes in the order shown in the illustration.

    Torque:
    26.5 N*m{ 270 kgf*cm , 20 ft.*lbf }

    If a mounting bolt does not meet the torque specification, replace it.



    G035063E01
  1. Mark the mounting bolts with paint.

  1. Retighten the mounting bolts by 90° in the numerical order shown in the illustration.



    G035062E02
  1. Check that the painted marks are now at a 90° angle to the previous position.



31. INSTALL CLUTCH DISC


    C147158E01
  1. Insert SST into the clutch disc. Then insert the SST (together with the clutch disc) into the flywheel.

    SST
    09301-00110  

    NOTICE:
    Take care not to insert the clutch disc facing the wrong direction.



32. INSTALL CLUTCH COVER


    D029623E04
  1. Align the matchmarks on the clutch cover and flywheel.

  1. Tighten the 6 bolts as described below.

    1. Determine the first bolt to be tightened by choosing the bolt closest to the knock pin.

    2. Uniformly tighten the 6 bolts in diametrically opposite pairs relative to the position of the first bolt. Use the illustration as a reference.

      Torque:
      19 N*m{ 195 kgf*cm , 14 in.*lbf }

  1. Lightly move SST up and down, and right and left.

    SST
    09301-00110  

  1. Check that the disc is in the center, and then tighten the bolts.



33. INSTALL MANUAL TRANSMISSION UNIT
  1. Install the manual transmission unit (Click here).



34. INSTALL CLUTCH RELEASE CYLINDER
  1. Install the clutch release cylinder with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



35. INSTALL STARTER


    G039103E03
  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Install the starter wire to terminal 30 with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Attach the terminal cap.

  1. Connect the starter connector.



36. INSTALL REAR PROPELLER SHAFT ASSEMBLY


C118613E01
  1. Align the matchmarks on the propeller shaft flange and transfer flange.

  1. Connect the propeller shaft with the 4 washers and 4 nuts.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }

  1. Align the matchmarks on the propeller shaft flange and differential flange.



    C118614E01
  1. Install the propeller shaft with the 4 bolts, 4 washers and 4 nuts.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



37. INSTALL FRONT PROPELLER SHAFT ASSEMBLY


F052086E01
  1. Align the matchmarks on the yoke and transfer flange.

  1. Connect the propeller shaft with the 4 washers and 4 nuts.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



    C098708E01
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the front propeller shaft with the 4 bolts, 4 washers and 4 nuts.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



38. INSTALL FRONT EXHAUST PIPE


    A107610
  1. Using a vernier caliper, measure the free length of the compression spring.

    Minimum length:
    40 mm (1.57 in.)

    If the length is less than the minimum, replace the compression spring.

  1. Install the front pipe to the pipe support.



    A099436E06
  1. Install a new gasket to the exhaust manifold.

    HINT:
    Using a plastic-faced hammer, uniformly strike the gasket so that the gasket and exhaust manifold are properly fit.

    NOTICE:
    1. Be careful with the installation direction of the gasket.
    2. Do not reuse the gasket.
    3. To ensure a proper seal, do not use the front pipe to force the gasket onto the exhaust manifold.

  1. Install the front pipe with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



39. INSTALL HOOD ASSEMBLY
  1. Install the hood with the 4 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Connect the washer nozzle hose.

  1. Adjust the hood (Click here).



40. INSTALL COOLER COMPRESSOR


    A099200E01
  1. Loosely install the bolt labeled A to install the compressor.

  1. Install the compressor completely by tightening the 4 bolts in the order shown in the illustration.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    NOTICE:
    In order to prevent misalignment, which causes belt rattle, tightening of the bolts must be performed in the order shown.



    A099198E01
  1. Connect the suction hose with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the compressor connector.



41. INSTALL OIL DIPSTICK GUIDE
  1. Install a new O-ring and the dipstick guide with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



42. INSTALL OIL DIPSTICK


43. INSTALL VANE PUMP


    A099199E01
  1. Install the vane pump with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the PS oil pressure switch connector.



44. CONNECT ENGINE WIRE


    G038831E01
  1. Connect the 2 engine room junction block connectors and connect the wire clamp.

  1. Connect the cable to the engine room junction block with the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Install the engine room relay block cover (upper).

  1. Install the engine room relay block cover (side).

  1. Connect the ground wire with the bolt and clamp.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }



    A112963E01
  1. Connect the ground wire to the frame with the bolt so that it is within the range shown in the illustration.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Push the engine wire through the dash panel into the cabin. The wire should be within the range shown in the illustration.

  1. Connect the sensor clamp with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A111959
  1. Connect the ECM connectors.

    1. Connect the 4 ECM connectors.

    2. Install the glove compartment door.

  1. Connect the wire clamp to the engine mounting bracket front LH with the bolt.



45. CONNECT FUEL HOSE


    G039233E04
  1. Connect the No. 2 fuel hose to the pressure regulator.



  1. Connect the No. 1 fuel hose to the pulsation damper.



      A071366E09
    1. Check that there is no damage or contamination in the connected part of the pipe.

    2. Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh engine oil on the tip of the pipe.



    3. A071366E10
    4. After having finished the connection, try to pull apart the pipe and the connector and confirm that they are securely connected.



    5. A099425E05
    6. Attach the lock claws to the connector by pushing down on the cover, as shown in the illustration.



46. CONNECT HOSE


    G039232E01
  1. Connect the vacuum hose to the intake manifold.

  1. for Unleaded Gasoline Specification Vehicle:
    Connect the hose to the purge VSV.



47. INSTALL RADIATOR ASSEMBLY


    A099640E02
  1. Install the radiator with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    A110375
  1. Attach the 4 clamps to the radiator side as shown in the illustration.

  1. Connect the 2 front airbag sensor connectors.



48. INSTALL FAN PULLEY


49. INSTALL FAN SHROUD


A099679E03
  1. Install the fan pulley to the water pump.

  1. Place the shroud together with the fluid coupling fan between the radiator and engine.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Install the coupling fan to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.

  1. Attach the shroud's claws to the radiator as shown in A in the illustration.

  1. Install the shroud with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the reservoir hose to the radiator tank upper.

  1. Install the drive belt (Click here).

  1. Tighten the 4 nuts of the fluid coupling fan.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



50. INSTALL DRIVE BELT


    A097752E04
  1. Install the drive belt to all the pulleys except the drive belt tensioner pulley.

  1. Use the hexagon-shaped part indicated by the arrow in the illustration to move the tensioner pulley downward and then install the drive belt to the tensioner pulley.

    NOTICE:
    1. The backside of the drive belt should face the tensioner pulley.
    2. Check that the drive belt is properly set to each pulley.



    G038479E01
  1. After a new belt has been installed, check that the tensioner indicator mark is within range A shown in the illustration.



51. CONNECT RADIATOR OUTLET HOSE


52. CONNECT RADIATOR INLET HOSE


53. INSTALL RADIATOR GRILLE
  1. Attach the 6 claws to install the radiator grille.

  1. Install the 2 screws and 2 clips.



54. INSTALL INTAKE AIR CONNECTOR AND AIR CLEANER ASSEMBLY


    A099871E01
  1. Install the air cleaner and intake air connector assembly with the 4 bolts, and tighten the hose clamp.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } for air cleaner
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf } for intake air connector
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } for hose clamp

  1. Connect the MAF meter connector and harness clamps.

  1. Connect the No. 2 ventilation hose.

  1. Connect the vacuum hose.



55. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


56. ADD ENGINE OIL
  1. Clean and install the oil drain plug with a new gasket.

    Torque:
    37.5 N*m{ 382 kgf*cm , 28 ft.*lbf }

  1. Add fresh engine oil.

    Standard capacity:
    Item
    Specified Condition
    Drain and refill with oil filter change
    5.6 liters (5.9 US qts, 4.9 Imp. qts)
    Drain and refill without oil filter change
    5.3 liters (5.6 US qts, 4.6 Imp. qts)
    Dry fill
    6.3 liters (6.7 US qts, 5.5 Imp. qts)

  1. Install the oil filler cap.



57. ADD ENGINE COOLANT
  1. Tighten all the plugs and fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug

    Standard capacity:
    7.8 liters (8.2 US qts, 6.9 Imp. qts)

  1. Fill the radiator with TOYOTA SLLC to the F line.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Please contact your TOYOTA dealer for further details.

      NOTICE:
      Never use water as a substitute for engine coolant.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level drops below the F line, add TOYOTA SLLC to the F line.

  1. Install the radiator cap.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

    2. Maintain the engine speed at 2,500 to 3,000 rpm.

    3. Press the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When pressing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A112081E01
  1. Check the coolant level in the radiator reservoir.
    If the coolant level is below the L line, add SLLC to the reservoir F line.



58. INSPECT FOR FUEL LEAK
  1. Check that there are no fuel leaks after performing maintenance anywhere on the fuel system.
    If there are fuel leaks, repair or replace parts as necessary.



59. INSPECT FOR OIL LEAK
  1. Start the engine, and check that there are no oil leaks after performing maintenance.



60. INSPECT FOR FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A099675E01
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the cylinder block and head.



61. INSTALL NO. 1 ENGINE UNDER COVER
  1. Install the No. 1 under cover with the 4 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. Install the side cover RH with the 3 clips and 3 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. Install the side cover LH with the 3 clips and 3 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



62. INSPECT IGNITION TIMING
  1. Warm up the engine and stop the engine.

    NOTICE:
    A warmed up engine should have an engine coolant temperature of over 80°C (176°F), have an engine oil temperature of 60°C (140°F), and the engine rpm should be stabilized.



    C108852E03
  1. When using the intelligent tester:
    Check the ignition timing.

    1. Connect the intelligent tester to the DLC3.

    2. Start the engine and idle the engine.

    3. Turn the intelligent tester main switch ON.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

      Standard ignition timing:
      0 to 20° BTDC @ idle

      HINT:
      Please refer to the intelligent tester operator's manual for further details.



    H100769E32
  1. When not using the intelligent tester:
    Check the ignition timing.

    1. Using SST, connect a tachometer tester probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

      NOTICE:
      1. Confirm the terminal number before connecting SST. Connection with a wrong terminal can damage the engine.
      2. Turn off all electrical systems before connecting SST.



    2. A099874E01
    3. Clamp a timing light tester probe to the No. 1 cylinder ignition coil connector's 4 lead wires or green-red lead wire.

    4. Start the engine.



    5. H100769E09
    6. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      When checking the ignition timing, the transmission should be in the neutral position.


      HINT:
      A099876E01
      1. After connecting terminals TC and CG, the engine rpm changes to approximately 1,000 to 1,500 rpm for 5 seconds, and then returns to idle speed. This occurs because the ECM checks that the ISC (idle speed control system) is operating properly.
      2. Perform the inspection of the ignition timing after the engine rpm has returned to idle speed.



    7. A099880E01
    8. Using a timing light, measure the ignition timing.

      Standard ignition timing:
      3 to 7° BTDC @ idle

    9. Remove SST from terminals 13 (TC) and 4 (CG) of the DLC3.

    10. Check the ignition timing.

      Standard ignition timing:
      0 to 20° BTDC @ idle

    11. Confirm that the ignition timing moves to the advanced angle side when the engine speed is increased.

    12. Remove the timing light.



63. CHECK IDLE SPEED
  1. Warm up and stop the engine.

    NOTICE:
    A warmed up engine should have an engine coolant temperature of over 80°C (176°F), have an engine oil temperature of 60°C (140°F), and the engine rpm should be stabilized.



  1. When using the intelligent tester:
    Check the idle speed.



      C108852E03
    1. Connect the intelligent tester to the DLC3.

      HINT:
      Please refer to the intelligent tester operator's manual for further details.

    2. Start the engine and idle the engine.

    3. Turn the intelligent tester main switch ON.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine SPD.

      Standard idle speed:
      600 to 700 rpm

      NOTICE:
      1. When checking the idle speed, the transmission should be in the neutral position.
      2. Switch off all accessories and the air conditioning before connecting the intelligent tester.



    H100769E32
  1. When not using the intelligent tester:
    Check the idle speed.

    1. Using SST, connect a tachometer tester probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

      NOTICE:
      1. Confirm the terminal number before connecting SST. Connection with a wrong terminal can damage the engine.
      2. Turn off all electrical systems before connecting SST.

    2. Start the engine and idle the engine.

    3. Check the idle speed.

      Standard idle speed:
      600 to 700 rpm



64. CHECK CO (for Leaded Gasoline Specification Vehicle)

HINT:
This check is used only to determine whether or not the idle CO complies with regulations.

  1. Initial condition:

    1. Engine at normal operating temperature

    2. Air cleaner installed

    3. All pipes and hoses of air induction system connected

    4. All accessories switched OFF

    5. All vacuum lines properly connected

    6. SFI system wiring connectors fully seated

    7. Ignition timing set correctly

    8. Transmission in neutral position

    9. Tachometer and CO meter calibration at idle

      NOTICE:
      If a CO meter is not available, do not attempt to adjust the idle mixture. Always use a CO meter when adjusting the idle mixture. Use of the idle mixture screw for adjustments is typically not necessary if the vehicle is in good condition.

  1. Warm up the engine at a constant speed (approximately 50 km/h (31 mph)). Close the throttle valve for 5 minutes after the engine coolant temperature becomes stable (80 to 90°C (176 to 194°F)) and idle the engine for 5 minutes.



    G038860E03
  1. Insert a tester probe at least 40 cm (1.3 ft.) into the tailpipe.

  1. Wait at least 1 minute before measuring to allow the concentration to stabilize. Complete the measuring within 3 minutes.

    Standard idle CO concentration:
    0.5 to 2.5%



    A001435E03
  1. If the CO concentration does not conform to regulations, adjust it by turning the idle mixture adjusting screw in the variable resistor with SST.

    SST
    09243-00020  



    A001434E02
  1. The idle mixture adjusting screw can be adjusted within a 180° angle range.
    If the CO concentration is within the specification, this adjustment is complete.
    If the CO concentration cannot be corrected by idle mixture adjustment, see the table below for other possible causes.

    CO
    Problems
    Causes
    High
    Rough idle
    (black smoke from exhaust)
    1. Clogged air filter
    2. Plugged ventilation valve
    3. Faulty SFI system
      1. Faulty fuel pressure regulator
      2. Clogged fuel pressure regulator
      3. Defective engine coolant temperature (ECT) sensor
      4. Faulty ECM
      5. Faulty injectors
      6. Faulty throttle position sensor
      7. Faulty MAF meter



65. CHECK CO/HC (for Unleaded Gasoline Specification Vehicle)
  1. Start and warm up the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds and idle the engine.



    G038860E01
  1. Insert a CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe.

  1. Check the CO/HC concentration at idle.

    Idle CO concentration:
    0 to 0.5%

    Idle HC concentration:
    Applicable local regulation

  1. If the CO/HC concentration is not as specified, perform troubleshooting in the order given below.

    1. Check the heated oxygen sensor operation (Click here).

    2. See the table below for possible causes, and then inspect and repair the applicable causes as necessary.

      CO
      HC
      Problems
      Causes
      Normal
      High
      Rough idle
      1. Faulty ignitions:
        1. Incorrect timing
        2. Plugs are contaminated, shorted or gaps are defective
      2. Incorrect valve clearance
      3. Leaks in intake and exhaust valves
      4. Leaks in cylinders
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. Ventilation hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Plugged ventilation valve
      3. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective ECT sensor
        3. Defective Mass Air Flow (MAF) meter
        4. Faulty ECM
        5. Faulty injectors
        6. Faulty throttle position sensor



66. CHECK FUNCTION OF THROTTLE BODY


    A111693
  1. Check the throttle control motor operating sound.

    1. Turn the ignition switch ON.

    2. When pressing the accelerator pedal, check the operating sound of the running motor. Make sure that no friction noises emit from the motor.
      If friction noise is heard, replace the throttle body.



    A099015E01
  1. Check the throttle position sensor.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch ON.

    3. Under Current Data, check that the throttle valve opening percentage (Throttle Pos) is within the standard.

      Standard throttle valve opening percentage:
      60% or more

      NOTICE:
      When checking the standard throttle valve opening percentage, the shift lever should be in the N position.

      If the percentage is less than 60%, replace the throttle body.