DTC P0100/31 Mass Air Flow Circuit Malfunction |
DTC P0102/31 Mass or Volume Air Flow Circuit Low Input |
DTC P0103/31 Mass or Volume Air Flow Circuit High Input |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0100/31 | When the MAF meter circuit is open or shorted for more than 3 seconds |
|
| P0102/31 | When the MAF meter circuit is open for more than 3 seconds |
|
| P0103/31 | When the MAF meter circuit is shorted for more than 3 seconds |
|
| Air Flow Value (g/sec.) | Malfunction |
| Approximately 0 |
|
| 271.0 or more | Open in E2G circuit |

| 1.READ DATA LIST (MASS AIR FLOW RATE) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the values.
| Mass Air Flow Rate (g/sec.) | Proceed to |
| Approximately 0.0 | A |
| 271.0 or more | B |
| Between 0.0 and 271.0* | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK MASS AIR FLOW METER (POWER SOURCE) |
![]() |
Disconnect the A4 MAF meter connector.
Turn the ignition switch ON.
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| A4-1 (+B) - Body ground | 9 to 14 V |
|
| ||||
| OK | |
| 3.CHECK ECM (VG VOLTAGE) |
![]() |
Start the engine.
Measure the voltage of the ECM connector.
| Tester Connection | Condition | Specified Condition |
| E10-28 (VG) - E10-30 (E2G) | Engine is idling | 0.5 to 3.0 V |
|
| ||||
| NG | |
| 4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() |
Disconnect the A4 MAF meter connector.
Disconnect the E10 ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| A4-3 (VG) - E10-28 (VG) | Below 1 Ω |
| A4-2 (E2G) - E10-30 (E2G) | Below 1 Ω |
| A4-3 (VG) or E10-28 (VG) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - INTEGRATION RELAY (MAIN RELAY)) |
![]() |
Disconnect the A4 MAF meter connector.
Remove the integration relay from the engine room junction block (Click here).
Disconnect the 1J integration relay connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| A4-1 (+B) - 1J-5 | Below 1 Ω |
| A4-1 (+B) or 1J-5 - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.CHECK ECM (SENSOR GROUND) |
![]() |
Measure the resistance of the E10 ECM connector.
| Tester Connection | Specified Condition |
| E10-30 (E2G) - Body ground | Below 1 Ω |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() |
Disconnect the A4 MAF meter connector.
Disconnect the E10 ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| A4-3 (VG) - E10-28 (VG) | Below 1 Ω |
| A4-2 (E2G) - E10-30 (E2G) | Below 1 Ω |
| A4-3 (VG) or E10-28 (VG) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 1.CHECK ECM (VG VOLTAGE) |
![]() |
Start the engine.
Measure the voltage of the ECM connector.
| Tester Connection | Condition | Specified Condition |
| E10-28 (VG) - E10-30 (E2G) | Engine is idling | 0.5 to 3.0 V |
|
| ||||
| NG | |
| 2.CHECK MASS AIR FLOW METER (POWER SOURCE) |
![]() |
Disconnect the A4 MAF meter connector.
Turn the ignition switch ON.
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| A4-1 (+B) - Body ground | 9 to 14 V |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() |
Disconnect the A4 MAF meter connector.
Disconnect the E10 ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| A4-3 (VG) - E10-28 (VG) | Below 1 Ω |
| A4-2 (E2G) - E10-30 (E2G) | Below 1 Ω |
| A4-3 (VG) or E10-28 (VG) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - INTEGRATION RELAY (MAIN RELAY)) |
![]() |
Disconnect the A4 MAF meter connector.
Remove the integration relay from the engine room junction block (Click here).
Disconnect the 1J integration relay connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| A4-1 (+B) - 1J-5 | Below 1 Ω |
| A4-1 (+B) or 1J-5 - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||