FRONT DIFFERENTIAL CARRIER OIL SEAL > REPLACEMENT |
| 1. REMOVE NO. 1 ENGINE UNDER COVER |
| 2. REMOVE NO. 2 ENGINE UNDER COVER |
| 3. DRAIN DIFFERENTIAL OIL |
for front differential:
Stop the vehicle on a level surface.
![]() |
Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, remove the differential filler plug and gasket.
| *1 | 10 mm Straight Hexagon Wrench |
| *2 | 10 mm Union Nut Wrench |
| *3 | Socket Adaptor |
Remove the drain plug and gasket, and drain the oil.
Install a new gasket and the drain plug.
for rear differential:
Stop the vehicle on a level surface.
Remove the differential filler plug and gasket.
Remove the drain plug and gasket, and drain the oil.
Install a new gasket and the drain plug.
| 4. REMOVE FRONT PROPELLER SHAFT ASSEMBLY |
| 5. REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT |
![]() |
Using SST and a hammer, loosen the staked part of the nut.
![]() |
Using SST to hold the companion flange, remove the nut.
| *a | Turn |
| *b | Hold |
| 6. REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR |
![]() |
Using SST, remove the companion flange with dust deflector.
| 7. REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL |
![]() |
Using SST, remove the oil seal.
| *1 | Oil Seal |
| *2 | Oil Slinger |
| 8. REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER |
![]() |
Remove the oil slinger from the drive pinion.
| 9. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING |
![]() |
Using SST, remove the roller bearing (inner).
![]() |
Using SST, tap out the roller bearing (outer).
| 10. REMOVE FRONT DIFFERENTIAL OIL STORAGE RING |
Using a screwdriver and hammer, tap out the oil storage ring.
| 11. REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER |
Remove the bearing spacer from the drive pinion.
| 12. INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER |
![]() |
Install a new bearing spacer.
| 13. INSTALL FRONT DIFFERENTIAL OIL STORAGE RING |
Using a brass bar and hammer, tap in a new oil storage ring.
| 14. INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING |
![]() |
Using SST and a hammer, install the roller bearing (outer).
Install the roller bearing (inner).
| 15. INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER |
![]() |
Install the oil slinger to the drive pinion.
| 16. INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL |
Apply MP grease to the lip of a new oil seal.
![]() |
Using SST and a hammer, tap in the oil seal.
| *a | Oil Seal Depth |
| 17. INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR |
![]() |
Using SST, install the companion flange with dust deflector.
Apply hypoid gear oil LSD to drive pinion thread and nut seat face.
![]() |
Using SST to hold the companion flange, install a new nut.
| *a | Turn |
| *b | Hold |
| 18. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD |
![]() |
Using a torque wrench, measure the preload.
| Item | Specified Condition |
| New bearing | 1.0 to 1.5 N*m (11 to 15 kgf*cm, 9 to 13 in.*lbf) |
| Reused bearing | 0.5 to 0.7 N*m (6 to 7 kgf*cm, 5 to 6 in.*lbf) |
| 19. INSPECT TOTAL PRELOAD |
![]() |
Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.
| 20. STAKE FRONT DRIVE PINION COMPANION FLANGE NUT |
![]() |
Using a chisel and hammer, stake the nut.
| 21. INSTALL FRONT PROPELLER SHAFT ASSEMBLY |
| 22. ADD DIFFERENTIAL OIL |
![]() |
Add differential oil so that the oil level is within 5 mm (0 to 0.196 in.) from the bottom lip of the differential filler plug hole.
| Temperature | Viscosity |
| Above -18°C (0°F) | SAE 90 |
| Below -18°C (0°F) | SAE 80W-90 or SAE 80W |
| Item | Specified Condition |
| Front differential (4WD) | Hypoid gear oil API GL-4 or GL-5 |
| Rear differential | Hypoid gear oil API GL-5 |
| Item | Specified Condition |
| Standard | 3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.90 to 2.99 Imp. qts.) |
| w/ Differential lock | 2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.60 Imp. qts.) |
| Made for DANA | 2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.) |
Check for oil leakage when the oil level is low.
for front differential:
![]() |
Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, install a new gasket and the differential filler plug.
| *1 | 10 mm Straight Hexagon Wrench |
| *2 | 10 mm Union Nut Wrench |
| *3 | Socket Adaptor |
for rear differential:
Install a new gasket and the differential filler plug.
| 23. INSTALL NO. 2 ENGINE UNDER COVER |
Install the under cover with the 4 bolts.
| 24. INSTALL NO. 1 ENGINE UNDER COVER |
Install the under cover with the 8 bolts.