Home › DRIVE LINE › DIFFERENTIAL › DIFFERENTIAL CARRIER OIL SEAL

DIFFERENTIAL CARRIER OIL SEAL > REPLACEMENT

for Preparation Click here



1. DRAIN DIFFERENTIAL OIL


  1. for front differential:

    1. Stop the vehicle on a level surface.



    2. A272242E01
    3. Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, remove the differential filler plug and gasket.

      SST
      09961-00950  
      Text in Illustration 
      *1
      10 mm Straight Hexagon Wrench
      *2
      10 mm Union Nut Wrench
      *3
      Socket Adaptor

    4. Remove the drain plug and gasket, and drain the oil.

    5. Install a new gasket and the drain plug.

      Torque:
      65 N*m{ 660 kgf*cm , 48 ft.*lbf }

  1. for rear differential:

    1. Stop the vehicle on a level surface.

    2. Remove the differential filler plug and gasket.

    3. Remove the drain plug and gasket, and drain the oil.

    4. Install a new gasket and the drain plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }



2. REMOVE REAR PROPELLER SHAFT ASSEMBLY
(Click here)


3. REMOVE REAR DRIVE PINION NUT


    C236628E01
  1. Using SST and a hammer, loosen the staked part of the nut.

    SST
    09930-00010   (09931-00010, 09931-00020)



    C236629E01
  1. Using SST to hold the companion flange in place, remove the nut.

    SST
    09330-00021   (09330-00030)
    Text in Illustration 
    *a
    Turn
    *b
    Hold



4. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR


    C238724
  1. Using SST, remove the companion flange with dust deflector.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



5. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


    C236631E01
  1. Using SST, remove the oil seal.

    SST
    09308-10010  
    Text in Illustration 
    *1
    Oil Seal
    *2
    Oil Slinger



6. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


    C237315
  1. Remove the oil slinger from the drive pinion.



7. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C236632E01
  1. Using SST, remove the roller bearing (inner).

    SST
    09556-22010  



    C236633E01
  1. Using SST, tap out the roller bearing (outer).

    SST
    09308-00010  



8. REMOVE DIFFERENTIAL OIL STORAGE RING
  1. Using a screwdriver and hammer, tap out the oil storage ring.



9. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
  1. Remove the bearing spacer from the drive pinion.



10. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER


    C236634
  1. Install a new bearing spacer.

    HINT:
    Make sure the spacer is installed correctly.



11. INSTALL DIFFERENTIAL OIL STORAGE RING
  1. Using a brass bar and hammer, tap in a new oil storage ring.

    NOTICE:
    Be careful not to damage the oil storage ring.



12. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C236635E01
  1. Using SST and a hammer, tap in the roller bearing (outer).

    SST
    09316-60011   (09316-00011, 09316-00021)

  1. Install the roller bearing (inner).



13. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


    C237315
  1. Install the oil slinger to the drive pinion.



14. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL
  1. Apply MP grease to the lip of the oil seal.



    C236636E01
  1. Using SST and a hammer, tap in a new seal.

    SST
    09554-30011  
    Text in Illustration 
    *a
    Oil Seal Depth

    Standard oil seal depth:
    0 +/-0.3 mm (0 +/-0.0118 in.)



15. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR


    C238725
  1. Using SST, install the companion flange with dust deflector.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.

  1. Apply hypoid gear oil LSD to drive pinion thread and nut seat face.



    C237316E01
  1. Using SST to hold the companion flange in place, install a new nut.

    SST
    09330-00021   (09330-00030)
    Text in Illustration 
    *1
    Turn
    *1
    Hold

    Torque:
    370 N*m{ 3773 kgf*cm , 273 ft.*lbf } or less



16. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


    C236639
  1. Using a torque wrench, measure the preload.

    Standard Preload (Starting Torque):
    Bearing
    Specified Condition
    New
    1.1 to 1.6 N*m (12 to 16 kgf*cm, 10 to 14 in.*lbf)
    Reused
    0.6 to 0.8 N*m (7 to 8 kgf*cm, 6 to 7 in.*lbf)

    1. If the result is not as specified, adjust the preload .



17. INSPECT TOTAL PRELOAD


    C236639
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Standard Total Preload:
    Bearing
    Specified Condition
    New
    0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload
    Reused
    0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload

    1. If the result is not as specified, adjust the preload.



18. STAKE REAR DRIVE PINION NUT


    C236640
  1. Using a chisel and hammer, stake the nut.



19. INSTALL REAR PROPELLER SHAFT ASSEMBLY
(Click here)


20. ADD DIFFERENTIAL OIL


D025304E51
  1. Add differential oil so that the oil level is within 5 mm (0 to 0.196 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. After changing the oil, drive the vehicle, and then check the oil level again.
    2. Too much or too little oil will lead to differential problems.

    If necessary, fill the differential carrier assembly with hypoid gear oil.

    Recommended viscosity:
    Temperature
    Viscosity
    Above -18°C (0°F)
    SAE 90
    Below -18°C (0°F)
    SAE 80W-90 or SAE 80W

    Standard oil grade:
    Item
    Specified Condition
    Front differential (4WD)
    Hypoid gear oil API GL-4 or GL-5
    Rear differential
    Hypoid gear oil API GL-5

    Standard front differential oil capacity:
    1.40 to 1.50 liters (1.48 to 1.59 US qts., 1.23 to 1.31 Imp. qts.)

    Standard rear differential oil capacity:
    Item
    Specified Condition
    Standard
    3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.90 to 2.99 Imp. qts.)
    w/ Differential lock
    2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.60 Imp. qts.)
    Made for DANA
    2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)

  1. Check for oil leakage when the oil level is low.



  1. for front differential:



      A272243E01
    1. Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, install a new gasket and the differential filler plug.

      SST
      09961-00950  
      Text in Illustration 
      *1
      10 mm Straight Hexagon Wrench
      *2
      10 mm Union Nut Wrench
      *3
      Socket Adaptor

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

      NOTICE:
      1. Make sure all the tools are connected in a straight line.
      2. Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

        Formula:
        T' = T x L3 / (L1 + L2 + L3)
        - T' = Spec. value of torque wrench
        - T = Value of specified tightening torque
        - L1 = Length of union nut wrench
        - L2 = Length of SST
        - L3 = Length of torque wrench

  1. for rear differential:

    1. Install a new gasket and the differential filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }