Home › DRIVE LINE › DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY

FRONT DIFFERENTIAL CARRIER ASSEMBLY > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT DIFFERENTIAL SIDE GEAR SHAFT BEARING RH


    C237492E01
  1. Using SST and a press, press in the shaft bearing.

    SST
    09223-00010  

  1. Using a snap ring expander, install the snap ring.

    HINT:
    Install the snap ring securely.



2. INSTALL DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH
  1. Install the shaft to the differential tube.



    C237490
  1. Using a snap ring expander, install the snap ring.

    HINT:
    Install the snap ring securely.



3. INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL RH


    C236643E01
  1. Using SST and a hammer, tap in 2 new oil seals.

    SST
    09554-47010  
    09950-70010   (09951-07100)

    NOTICE:
    1. Make sure the LH and RH oil seals are installed to the proper locations.
    2. As a different side of SST is used for each oil seal, be sure to confirm that the correct side of SST is being used before tapping in an oil seal.
    3. Make sure that the lip of the oil seal is inserted into SST before tapping in the oil seal.
    4. As each side of SST is designed to tap in the corresponding oil seal to the proper depth, be sure to fully tap in the oil seal.
    5. Do not damage the oil seals.

    Standard Oil Seal Depth:
    Item
    Specified Condition
    for LH Side
    2.9 +/-0.45 mm (0.114 +/-0.0177 in.)
    for RH Side
    8.1 +/-0.45 mm (0.319 +/-0.0177 in.)

    Text in Illustration 
    *a
    for LH Side
    *b
    for RH Side
    *1
    Differential
    *2
    Seal

  1. Apply MP grease to the lip of each oil seal.



4. ASSEMBLE DIFFERENTIAL CASE


    C237493
  1. Install the 2 thrust washers to the 2 side gears.

    HINT:
    Using the table below, select 2 thrust washers which will ensure that the backlash is within the specifications.

    Standard Thrust Washer Thickness:
    Thickness mm (in.)
    Thickness mm (in.)
    1.48 to 1.52 (0.0583 to 0.0598)
    1.73 to 1.77 (0.0682 to 0.0696)
    1.53 to 1.57 (0.0603 to 0.0618)
    1.78 to 1.82 (0.0701 to 0.0716)
    1.58 to 1.62 (0.0623 to 0.0637)
    1.83 to 1.87 (0.0721 to 0.0736)
    1.63 to 1.67 (0.0642 to 0.0657)
    1.88 to 1.92 (0.0741 to 0.0755)
    1.68 to 1.72 (0.0662 to 0.0677)
    -



    C236669
  1. Install the 2 side gears, 2 pinion gears, 2 side gear thrust washers, 2 pinion gear thrust washers and pinion shaft to the differential case.

    HINT:
    Align the holes of the differential case and pinion shaft.



  1. Measure the side gear backlash.



      C236672
    1. Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case.

      Standard backlash:
      0.15 mm (0.00591 in.) or less

      If the backlash is not as specified, install 2 side gear thrust washers with different thicknesses.



    C236668
  1. Using a pin punch and hammer, tap in the straight pin through the differential case and hole of the pinion shaft.

  1. Stake the differential case.



5. INSTALL DIFFERENTIAL RING GEAR
  1. Clean the contact surface of the differential case and ring gear.

  1. Heat the ring gear in boiling water that is approximately 100°C (212°F).

  1. Carefully remove the ring gear from the boiling water.

  1. After the moisture on the ring gear has completely evaporated, quickly install the ring gear to the differential case.



    C237487E01
  1. Align the matchmarks on the ring gear and differential case.
    Text in Illustration 
    *1
    Matchmark

  1. After the ring gear cools down, apply thread lock adhesive to the 10 set bolts and install them.

    Thread lock:
    Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent

    Torque:
    97 N*m{ 984 kgf*cm , 71 ft.*lbf }



6. INSTALL FRONT DIFFERENTIAL CASE BEARING


    C237495E01
  1. Using SST and a press, press the bearing onto the differential case.

    SST
    09950-60010   (09951-00520, 09951-00610)
    09950-70010   (09951-07150)



7. INSTALL FRONT DIFFERENTIAL CASE BEARING

HINT:
When replacing the 2 differential case bearings, install the thinnest washer to each bearing. When reusing the bearings, install a new washer of the same thickness as the one that was removed to each bearing.



    C237496E01
  1. Using SST and a press, press in the case bearing (outer) to the differential side bearing retainer.

    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07150)



    C237497E01
  1. Using SST and a press, press in the case bearing (outer) to the differential carrier.

    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07150)



8. INSTALL BEARING OUTER RACE


    C237498E01
  1. Using SST, install the outer race (front).

    SST
    09950-60020   (09951-00720, 09951-00890)
    Text in Illustration 
    *a
    for Front
    *b
    for Rear
    *c
    Turn
    *d
    Hold

  1. Using a brass bar and hammer, tap in a new oil storage ring.

  1. Using SST, install the outer race (rear).

    SST
    09950-60020   (09951-00720, 09951-00890)



9. INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING
  1. Install the washer to the drive pinion.

    HINT:
    First, install a washer that has the same thickness as the removed washer. After checking the tooth contact pattern, replace the washer with one of a different thickness if necessary.



    C236679E01
  1. Using SST and a press, press the front bearing onto the drive pinion.

    SST
    09506-30012  



10. ADJUST DIFFERENTIAL DRIVE PINION PRELOAD


    C237303
  1. Install the drive pinion, rear drive pinion tapered roller bearing (inner) and oil slinger.

    HINT:
    Install the spacer and oil seal after adjusting the gear contact pattern.



    C237304E01
  1. Using SST, install the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.

  1. Adjust the drive pinion preload by tightening the companion flange nut.



    C237316E01
  1. Using SST to hold the flange in place, tighten the nut.

    SST
    09330-00021   (09330-00030)
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    Torque:
    370 N*m{ 3773 kgf*cm , 273 ft.*lbf } or less

    NOTICE:
    1. As there is no spacer, tighten the nut a little at a time. Be careful not to overtighten it.
    2. Apply hypoid gear oil LSD to drive pinion thread and nut seat face.



    C237317
  1. Using a torque wrench, measure the preload.

    Standard Preload (Starting Torque):
    Item
    Specified Condition
    New bearing
    0.7 to 1.2 N*m (8 to 12 kgf*cm, 7 to 10 in.*lbf)
    Reused bearing
    0.2 to 0.4 N*m (2 to 4 kgf*cm, 2 to 3 in.*lbf)

    NOTICE:
    1. For a more accurate measurement, rotate the bearing forward and backward several times before measuring.
    2. Record the differential drive pinion preload for the total preload measurement.



11. INSTALL DIFFERENTIAL CASE ASSEMBLY


12. ADJUST DIFFERENTIAL RING GEAR BACKLASH
  1. Install the side bearing retainer with the 10 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



    C237478E01
  1. Using SST and a dial indicator, measure the ring gear backlash.

    SST
    09564-33010  

    Standard backlash:
    0.11 to 0.21 mm (0.00433 to 0.00826 in.)

    If the backlash is not as specified, adjust it by either increasing or decreasing the number of washers on both sides equally.

    HINT:
    There should be no clearance between the plate washer and case. Make sure that the ring gear has backlash.


    Standard Washer Thickness:

    Thickness mm (in.)
    Thickness mm (in.)
    Thickness mm (in.)
    1.57 to 1.59 (0.0619 to 0.0625)
    1.79 to 1.81 (0.0705 to 0.0712)
    2.01 to 2.03 (0.0792 to 0.0799)
    1.59 to 1.61 (0.0626 to 0.0633)
    1.81 to 1.83 (0.0713 to 0.0720)
    2.03 to 2.05 (0.0780 to 0.0807)
    1.61 to 1.63 (0.0634 to 0.0641)
    1.83 to 1.85 (0.0721 to 0.0728)
    2.05 to 2.07 (0.0808 to 0.0814)
    1.63 to 1.65 (0.0642 to 0.0649)
    1.85 to 1.87 (0.0729 to 0.0736)
    2.07 to 2.09 (0.0815 to 0.0822)
    1.65 to 1.67 (0.0650 to 0.0657)
    1.87 to 1.89 (0.0737 to 0.0744)
    2.09 to 2.11 (0.0823 to 0.0830)
    1.67 to 1.69 (0.0658 to 0.0665)
    1.89 to 2.01 (0.0745 to 0.0791)
    2.11 to 2.13 (0.0831 to 0.0838)
    1.69 to 1.71 (0.0666 to 0.0673)
    1.91 to 1.93 (0.0752 to 0.0759)
    2.13 to 2.15 (0.0839 to 0.0846)
    1.71 to 1.73 (0.0674 to 0.0681)
    1.93 to 1.95 (0.0760 to 0.0767)
    2.15 to 2.17 (0.0847 to 0.0854)
    1.73 to 1.75 (0.0682 to 0.0688)
    1.95 to 1.97 (0.0768 to 0.0775)
    -
    1.75 to 1.77 (0.0689 to 0.0696)
    1.97 to 1.99 (0.0776 to 0.0783)
    -
    1.77 to 1.79 (0.0697 to 0.0704)
    1.99 to 2.01 (0.0784 to 0.0791)
    -



13. INSPECT TOTAL PRELOAD


    C237317
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Standard total preload (starting torque):
    0.3 to 0.8 N*m (4 to 8 kgf*cm, 3 to 7 in.*lbf) + drive pinion preload

    NOTICE:
    Record the differential ring gear preload.



14. ADJUST TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION
  1. Remove the differential case bearing retainer and differential case.

  1. Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.



    C237500
  1. Install the differential case and differential case bearing retainer.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Hold the companion flange firmly in place and rotate the ring gear in both directions.

  1. Remove the differential case bearing retainer and differential case.



  1. Inspect the tooth contact pattern.


    C205651E01



    C237312E01
  1. If the teeth are not contacting properly, use the following chart to select a proper washer.
    Text in Illustration 
    *1
    Drive Pinion Washer

    Standard Washer Thickness:

    Thickness mm (in.)
    Thickness mm (in.)
    Thickness mm (in.)
    1.69 to 1.71 (0.0666 to 0.0673)
    1.93 to 1.95 (0.0760 to 0.0767)
    2.17 to 2.19 (0.0855 to 0.0862)
    1.72 to 1.74 (0.0678 to 0.0685)
    1.96 to 1.98 (0.0772 to 0.0779)
    2.20 to 2.22 (0.0867 to 0.0874)
    1.75 to 1.77 (0.0689 to 0.0696)
    1.99 to 2.01 (0.0784 to 0.0791)
    2.23 to 2.25 (0.0878 to 0.0885)
    1.78 to 1.80 (0.0701 to 0.0708)
    2.02 to 2.04 (0.0796 to 0.0803)
    2.26 to 2.28 (0.0890 to 0.0897)
    1.81 to 1.83 (0.0713 to 0.0720)
    2.05 to 2.07 (0.0807 to 0.0814)
    2.29 to 2.31 (0.0902 to 0.0909)
    1.84 to 1.86 (0.0725 to 0.0732)
    2.08 to 2.10 (0.0819 to 0.0826)
    2.32 to 2.34 (0.0914 to 0.0921)
    1.87 to 1.89 (0.0737 to 0.0744)
    2.11 to 2.13 (0.0831 to 0.0838)
    -
    1.90 to 1.92 (0.0748 to 0.0755)
    2.14 to 2.16 (0.0843 to 0.0850)
    -



15. REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT


    C236628E01
  1. Using SST and a hammer, loosen the staked part of the nut.

    SST
    09930-00010   (09931-00010, 09931-00020)



    C236629E01
  1. Using SST to hold the companion flange, remove the nut.

    SST
    09330-00021   (09330-00030)
    Text in Illustration 
    *a
    Turn
    *b
    Hold



16. REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR


    C236630E01
  1. Using SST, remove the companion flange with dust deflector.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



17. REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER


    C237315
  1. Remove the oil slinger from the drive pinion.



18. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


    C237691E01
  1. Using SST, remove the roller bearing (inner) from the drive pinion.

    SST
    09556-22010  



19. REMOVE DIFFERENTIAL DRIVE PINION


20. INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER


    C238723
  1. Install a new bearing spacer to the drive pinion.



21. INSTALL DIFFERENTIAL DRIVE PINION


22. INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


    C237516E01
  1. Using SST and a hammer, install the roller bearing (outer).

    SST
    09316-60011   (09316-00011)

  1. Install the roller bearing (inner).



23. INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER


    C237315
  1. Install the oil slinger to the drive pinion.



24. INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL
  1. Apply MP grease to the lip of a new oil seal.



    C236636E01
  1. Using SST and a hammer, tap in the oil seal.

    SST
    09554-22010  
    Text in Illustration 
    *a
    Oil Seal Depth

    Standard oil seal depth:
    4.35 +/-0.45 mm (0.171 +/-0.0177 in.)



25. INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR


    C236637E01
  1. Using SST, install the companion flange with dust deflector.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.

  1. Apply hypoid gear oil LSD to drive pinion thread and nut seat face.



    C236638E01
  1. Using SST to hold the companion flange, install a new nut.

    SST
    09330-00021   (09330-00030)
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    Torque:
    370 N*m{ 3773 kgf*cm , 273 ft.*lbf } or less



26. INSTALL DIFFERENTIAL SIDE BEARING RETAINER
  1. Remove any old seal packing material from the side bearing retainer.

    NOTICE:
    Do not drop oil on the contact surfaces of the differential carrier and side bearing retainer.

  1. Clean residual seal packing material on the contact surface using gasoline or alcohol.



    C237503E01
  1. Apply seal packing to the side bearing retainer as shown in the illustration.
    Text in Illustration 
    *1
    Seal Packing

    Seal packing:
    Toyota Genuine seal packing 1281, Three Bond 1281 or equivalent

    HINT:
    Install the side bearing retainer within 3 minutes after applying seal packing.

  1. Install the side bearing retainer with the 10 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



27. INSPECT TOTAL PRELOAD
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Standard Preload (Starting Torque):
    Item
    Specified Condition
    New bearing
    1.0 to 1.5 N*m (11 to 15 kgf*cm, 9 to 13 in.*lbf) + ring gear preload
    Reused bearing
    0.5 to 0.7 N*m (6 to 7 kgf*cm, 5 to 6 in.*lbf) + ring gear preload

    If necessary, disassemble and inspect the differential.



28. INSPECT DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH


    C237478E01
  1. Using SST and a dial indicator, measure the ring gear backlash.

    SST
    09564-32011  

    Standard backlash:
    0.11 to 0.21 mm (0.00433 to 0.00826 in.)

    If the backlash is not within the specification, adjust the side bearing preload.



29. INSPECT FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C236648E01
  1. Using a dial indicator, measure the runout of the companion flange vertically and laterally.
    Text in Illustration 
    *a
    30 mm (1.18 in.)

    Maximum Runout:
    Item
    Specified Condition
    Vertical runout
    0.10 mm (0.00394 in.)
    Lateral runout
    0.10 mm (0.00394 in.)

    1. If the runout is more than the maximum, replace the companion flange.



30. STAKE FRONT DRIVE PINION FRONT COMPANION FLANGE NUT


    C236640
  1. Using a chisel and hammer, stake the nut.



31. INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL LH


    C236643E01
  1. Using SST and a hammer, tap in 2 new oil seals.

    SST
    09554-47010  
    09950-70010   (09951-07100)

    NOTICE:
    1. Make sure the LH and RH oil seals are installed to the proper locations.
    2. As a different side of SST is used for each oil seal, be sure to confirm that the correct side of SST is being used before tapping in an oil seal.
    3. Make sure that the lip of the oil seal is inserted into SST before tapping in the oil seal.
    4. As each side of SST is designed to tap in the corresponding oil seal to the proper depth, be sure to fully tap in the oil seal.
    5. Do not damage the oil seals.

    Standard Oil Seal Depth:
    Item
    Specified Condition
    for LH Side
    2.9 +/-0.45 mm (0.114 +/-0.0177 in.)
    for RH Side
    8.1 +/-0.45 mm (0.319 +/-0.0177 in.)

    Text in Illustration 
    *a
    for LH Side
    *b
    for RH Side
    *1
    Differential
    *2
    Seal

  1. Apply MP grease to the lip of each oil seal.



32. INSTALL DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH
  1. Install a new snap ring to the side shaft.

  1. Using a plastic-faced hammer, tap the side gear shaft into the differential case.

  1. Check that there is 2 to 3 mm (0.0788 to 0.118 in.) of axial play.

  1. Check that the side gear shaft cannot be completely pulled out by hand.



33. INSTALL FRONT DIFFERENTIAL TUBE ASSEMBLY
  1. Remove any old seal packing material on the contact surfaces of the differential and clutch case.

    NOTICE:
    Do not drop oil on the contact surfaces of the differential and clutch case.

  1. Clean residual seal packing material on the contact surface using gasoline or alcohol.



    C237504E01
  1. Apply seal packing to the differential as shown in the illustration.
    Text in Illustration 
    *1
    Seal Packing

    Seal packing:
    Toyota Genuine seal packing 1281, Three Bond 1281 or equivalent

    HINT:
    Install the differential tube within 3 minutes after applying seal packing.

  1. Install the differential tube to the differential.



    C237479
  1. Clean the threads of the 4 bolts and retainer bolt holes with toluene or trichloroethylene.

  1. Install the 4 bolts.

    Torque:
    110 N*m{ 1122 kgf*cm , 81 ft.*lbf }