Home › SUSPENSION & AXLE › SUSPENSION › FRONT WHEEL ALIGNMENT

FRONT WHEEL ALIGNMENT > ADJUSTMENT

for Preparation Click here



1. INSPECT TIRE
  1. Inspect the tires (Click here).



2. INSPECT VEHICLE HEIGHT


C125201E02

NOTICE:
Before inspecting the wheel alignment, adjust the vehicle height to the specification.

  1. Press down on the vehicle several times to stabilize the suspension, and measure the vehicle height.

    Standard Vehicle Height (for Unloaded Vehicle):
    Vehicle Model
    Front A - B
    Rear C - D
    GGN50R-NKASKN
    76 mm (2.99 in.)
    61 mm (2.40 in.)
    GGN60R-NKASKN
    71 mm (2.80 in.)
    56 mm (2.20 in.)
    KUN51L-NKMSYN
    78 mm (3.07 in.)
    59 mm (2.32 in.)
    KUN51R-NKMSYN
    78 mm (3.07 in.)
    59 mm (2.32 in.)
    KUN51R-NKPSYN
    79 mm (3.11 in.)
    59 mm (2.32 in.)
    KUN61R-NKMSYN
    72 mm (2.83 in.)
    57 mm (2.24 in.)
    KUN61R-NKPSYN
    73 mm (2.87 in.)
    57 mm (2.24 in.)
    KUN60R-NKMDHN
    71 mm (2.80 in.)
    56 mm (2.20 in.)
    LAN50L-NKMSEN
    75 mm (2.95 in.)
    59 mm (2.32 in.)
    LAN50R-NKMSEN
    75 mm (2.95 in.)
    59 mm (2.32 in.)
    TGN51L-NKMSKN
    76 mm (2.99 in.)
    59 mm (2.32 in.)
    KUN51R-KKPSY
    79 mm (3.11 in.)
    61 mm (2.40 in.)

    Measuring point:
    A:
    Ground clearance of front wheel center
    B:
    Ground clearance of lower suspension arm No. 1 set bolt center
    C:
    Ground clearance of rear wheel center
    D:
    Ground clearance of strut rod set bolt center

    1. If the vehicle height is not as specified, press down on the vehicle several times to stabilize the suspension. Then measure the vehicle height again.

    NOTICE:
    The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.



3. INSPECT TOE-IN


SA03213E04

Standard Toe-in (for Unloaded Vehicle):
Vehicle Model
A + B
C - D
GGN50R-NKASKN
A + B: 0°1' +/-5' (0.02° +/-0.09°)
C - D: 0.4 +/-1.0 mm (0.02 +/-0.04 in.)
GGN60R-NKASKN
A + B: 0°3' +/-5' (0.05° +/-0.09°)
C - D: 1.3 +/-1.0 mm (0.05 +/-0.04 in.)
KUN51L-NKMSYN
A + B: 0°1' +/-5' (0.01° +/-0.09°)
C - D: 0.2 +/-1.0 mm (0.01 +/-0.04 in.)
KUN51R-NKMSYN
A + B: 0°1' +/-5' (0.01° +/-0.09°)
C - D: 0.2 +/-1.0 mm (0.01 +/-0.04 in.)
KUN51R-NKPSYN
A + B: 0°00' +/-5' (0.00° +/-0.09°)
C - D: 0.1 +/-1.0 mm (0.01 +/-0.04 in.)
KUN61R-NKMSYN
A + B: 0°2' +/-5' (0.04° +/-0.09°)
C - D: 1.1 +/-1.0 mm (0.04 +/-0.04 in.)
KUN61R-NKPSYN
A + B: 0°2' +/-5' (0.04° +/-0.09°)
C - D: 1.0 +/-1.0 mm (0.04 +/-0.04 in.)
KUN60R-NKMDHN
A + B: 0°3' +/-5' (0.05° +/-0.09°)
C - D: 1.3 +/-1.0 mm (0.05 +/-0.04 in.)
LAN50L-NKMSEN
A + B: 0°2' +/-5' (0.03° +/-0.09°)
C - D: 0.7 +/-1.0 mm (0.03 +/-0.04 in.)
LAN50R-NKMSEN
A + B: 0°2' +/-5' (0.03° +/-0.09°)
C - D: 0.7 +/-1.0 mm (0.03 +/-0.04 in.)
TGN51L-NKMSKN
A + B: 0°1' +/-5' (0.02° +/-0.09°)
C - D: 0.5 +/-1.0 mm (0.02 +/-0.04 in.)
KUN51R-KKPSY
A + B: 0°1' +/-5' (0.01° +/-0.09°)
C - D: 0.1 +/-1.0 mm (0.01 +/-0.04 in.)

  1. If the toe-in is not as specified, adjust it at the rack ends.


4. ADJUST TOE-IN
  1. Detach the rack boot set clips.

  1. Loosen the tie rod end lock nuts.

  1. Turn the right and left rack ends by an equal amount to adjust the toe-in to the center value.

    HINT:
    The toe-in should be as close as possible to the center value.



    F050367E01
  1. Make sure that the lengths of the right and left rack ends are approximately the same.

    Standard difference:
    0 +/-1 mm (0 +/-0.039 in.)

  1. Tighten the tie rod end lock nuts.

    Torque:
    56 N*m{ 566 kgf*cm , 41 ft.*lbf }

  1. Place the boots on the seats and attach the clips.

    HINT:
    Make sure that the boots are not twisted.



5. INSPECT WHEEL ANGLE


SA00028E06
  1. Turn the steering wheel to the left and right full lock positions, and measure the wheel angle.

    Standard Wheel Angle (for Unloaded Vehicle):
    Inside Wheel Angle
    Outside Wheel Angle (Reference)
    34°42' (32°42' to 35°42')
    (34.70° (32.70° to 35.70°))
    31°54'
    (31.90°)

    1. If the angles are not as specified, check and adjust the right and left rack end lengths.



6. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION


Z003382E06
  1. Install a camber-caster-kingpin gauge or place the front wheels on the center of a wheel alignment tester.

  1. Inspect the camber, caster and steering axis inclination.

    Standard Camber Inclination (for Unloaded Vehicle):
    Vehicle Model
    Camber Inclination
    GGN50R-NKASKN
    Right-left error
    0°9' +/-30' (0.15° +/-0.50°)
    30' (0.50°) or less
    GGN60R-NKASKN
    Right-left error
    0°16' +/-30' (0.27° +/-0.50°)
    30' (0.50°) or less
    KUN51L-NKMSYN
    Right-left error
    0°8' +/-30' (0.13° +/-0.50°)
    30' (0.50°) or less
    KUN51R-NKMSYN
    Right-left error
    0°8' +/-30' (0.13° +/-0.50°)
    30' (0.50°) or less
    KUN51R-NKPSYN
    Right-left error
    0°7' +/-30' (0.12° +/-0.50°)
    30' (0.50°) or less
    KUN61R-NKMSYN
    Right-left error
    0°14' +/-30' (0.23° +/-0.50°)
    30' (0.50°) or less
    KUN61R-NKPSYN
    Right-left error
    0°14' +/-30' (0.23° +/-0.50°)
    30' (0.50°) or less
    KUN60R-NKMDHN
    Right-left error
    0°16' +/-30' (0.27° +/-0.50°)
    30' (0.50°) or less
    LAN50L-NKMSEN
    Right-left error
    0°12' +/-30' (0.20° +/-0.50°)
    30' (0.50°) or less
    LAN50R-NKMSEN
    Right-left error
    0°12' +/-30' (0.20° +/-0.50°)
    30' (0.50°) or less
    TGN51L-NKMSKN
    Right-left error
    0°10' +/-30' (0.17° +/-0.50°)
    30' (0.50°) or less
    KUN51R-KKPSY
    Right-left error
    0°7' +/-30' (0.12° +/-0.50°)
    30' (0.50°) or less

    Standard Caster Inclination (for Unloaded Vehicle):
    Vehicle Model
    Caster Inclination
    GGN50R-NKASKN
    Right-left error
    2°57' +/-30' (2.95° +/-0.50°)
    30' (0.50°) or less
    GGN60R-NKASKN
    Right-left error
    2°49' +/-30' (2.82° +/-0.50°)
    30' (0.50°) or less
    KUN51L-NKMSYN
    Right-left error
    2°52' +/-30' (2.87° +/-0.50°)
    30' (0.50°) or less
    KUN51R-NKMSYN
    Right-left error
    2°50' +/-30' (2.83° +/-0.50°)
    30' (0.50°) or less
    KUN51R-NKPSYN
    Right-left error
    2°51' +/-30' (2.85° +/-0.50°)
    30' (0.50°) or less
    KUN61R-NKMSYN
    Right-left error
    2°49' +/-30' (2.82° +/-0.50°)
    30' (0.50°) or less
    KUN61R-NKPSYN
    Right-left error
    2°49' +/-30' (2.82° +/-0.50°)
    30' (0.50°) or less
    KUN60R-NKMDHN
    Right-left error
    2°45' +/-30' (2.75° +/-0.50°)
    30' (0.50°) or less
    LAN50L-NKMSEN
    Right-left error
    2°52' +/-30' (2.87° +/-0.50°)
    30' (0.50°) or less
    LAN50R-NKMSEN
    Right-left error
    2°52' +/-30' (2.87° +/-0.50°)
    30' (0.50°) or less
    TGN51L-NKMSKN
    Right-left error
    2°53' +/-30' (2.88° +/-0.50°)
    30' (0.50°) or less
    KUN51R-KKPSY
    Right-left error
    2°54' +/-30' (2.90° +/-0.50°)
    30' (0.50°) or less

    Standard Steering Axis Inclination (for Unloaded Vehicle):
    Vehicle Model
    Steering Axis Inclination
    GGN50R-NKASKN
    Right-left error
    12°20' +/-30' (12.33° +/-0.50°)
    30' (0.50°) or less
    GGN60R-NKASKN
    Right-left error
    12°13' +/-30' (12.22° +/-0.50°)
    30' (0.50°) or less
    KUN51L-NKMSYN
    Right-left error
    12°21' +/-30' (12.35° +/-0.50°)
    30' (0.50°) or less
    KUN51R-NKMSYN
    Right-left error
    12°21' +/-30' (12.35° +/-0.50°)
    30' (0.50°) or less
    KUN51R-NKPSYN
    Right-left error
    12°22' +/-30' (12.37° +/-0.50°)
    30' (0.50°) or less
    KUN61R-NKMSYN
    Right-left error
    12°15' +/-30' (12.25° +/-0.50°)
    30' (0.50°) or less
    KUN61R-NKPSYN
    Right-left error
    12°15' +/-30' (12.25° +/-0.50°)
    30' (0.50°) or less
    KUN60R-NKMDHN
    Right-left error
    12°13' +/-30' (12.22° +/-0.50°)
    30' (0.50°) or less
    LAN50L-NKMSEN
    Right-left error
    12°17' +/-30' (12.28° +/-0.50°)
    30' (0.50°) or less
    LAN50R-NKMSEN
    Right-left error
    12°17' +/-30' (12.28° +/-0.50°)
    30' (0.50°) or less
    TGN51L-NKMSKN
    Right-left error
    12°19' +/-30' (12.32° +/-0.50°)
    30' (0.50°) or less
    KUN51R-KKPSY
    Right-left error
    12°22' +/-30' (12.37° +/-0.50°)
    30' (0.50°) or less

    1. If the camber and caster are not as specified, adjust them.
    1. If the steering axis inclination is not as specified after the camber and caster have been correctly adjusted, check the steering knuckle and front wheel for distortion or looseness.



7. ADJUST CAMBER AND CASTER

NOTICE:
After the camber has been adjusted, inspect the toe-in.

  1. Loosen the camber adjusting cam nut and camber adjusting cam bolt.



  1. Turn the No. 1 camber adjusting cam and No. 2 camber adjusting cam in both directions, and adjust the camber and caster to the center value.

    HINT:
    The camber and caster should be as close as possible to the center value.

    F049980E05



    C138176E02
  1. How to read the adjustment chart (using examples).

    1. Find the wheel alignment standard value applicable for the particular model.

    2. Mark the selected standard value on the adjustment chart.

      Standard value (reference):
      Camber
      Caster
      0°00' (0.00°)
      4°20' (4.30°)

    3. Mark the alignment value measured when the vehicle is unloaded on the adjustment chart.

      Measured value (reference):
      Camber
      Caster
      0°10' (0.17°)
      3°50' (3.83°)



    4. As shown in the chart, read the distance from the marked point to 0, and adjust the front and/or rear adjusting cams accordingly.

      Amount to turn adjusting cams (by gradation):
      No. 1 camber adjusting cam
      No. 2 camber adjusting cam
      +3.0 mm
      -1.5 mm



      C113155E06



8. PLACE FRONT WHEELS FACING STRAIGHT AHEAD (w/ VSC)


9. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION (w/ VSC)
(Click here)