Home › TRANSMISSION ยท A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Inspect the torque converter clutch (Click here).



2. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY


C187503E01
  1. Install the torque converter clutch to the automatic transmission.

  1. Using a vernier caliper and straightedge, measure dimension A between the contact surfaces of the transmission and engine, and the contact surfaces of the converter and drive plate.



    D025545E01
  1. Using a vernier caliper and straightedge, measure dimension B shown in the illustration. Check that B is greater than A.

    Standard:
    B = A + 1.00 mm (0.0394 in.) or more



3. INSTALL NO. 1 ENGINE MOUNTING INSULATOR REAR


G034522E01
  1. Install the engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }



4. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


G034259E01
  1. Install the transmission to the engine with the 5 bolts.

    Torque:
    71 N*m{ 724 kgf*cm , 53 ft.*lbf }



    G034258E01
  1. Hold the crankshaft pulley bolt with a wrench and install the 6 torque converter clutch mounting bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }



5. INSTALL STIFFENER PLATE


G034607E01
  1. Install the No. 2 end plate.

  1. Install the No. 4 cylinder block insulator.

  1. Install the stiffener plate LH to the engine and transmission with the 4 bolts.

    Torque:
    71 N*m{ 720 kgf*cm , 53 ft.*lbf }

  1. Install the stiffener plate RH (with clamp tube) to the engine and transmission with the 4 bolts.

    Torque:
    71 N*m{ 720 kgf*cm , 53 ft.*lbf }



6. CONNECT WIRE HARNESS


7. CONNECT CONNECTOR
  1. Connect the connectors.

    1. Connect the temperature sensor connector.

    2. Connect the park/neutral position switch connector.

    3. Connect the 3 speed sensor connectors.

    4. Connect the transmission wire connector.



8. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


G034517E01
  1. *1: Install the 4 set bolts of the engine mounting insulator.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

  1. *2: Install the frame crossmember with the 4 bolts and 4 nuts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



9. INSTALL STARTER ASSEMBLY
  1. Install the starter (Click here).



10. INSTALL TRANSMISSION CONTROL CABLE BRACKET


G034516E01
  1. Install the control cable bracket with the 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



11. CONNECT TRANSMISSION CONTROL SHIFT CABLE ASSEMBLY


G034515E01
  1. Connect the control cable with the clip.

  1. Connect the control cable with the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



12. INSTALL OIL COOLER TUBE


G034255E02
  1. Loosely install the tip of the oil cooler tube inlet to the automatic transmission by hand.

  1. Loosely install the tip of the oil cooler tube outlet to the automatic transmission by hand.

  1. Install the 3 clamps with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } for A and B
    12 N*m{ 122 kgf*cm , 9 ft.*lbf } for C



    G034851E02
  1. Using a union nut wrench, tighten the inlet and outlet tubes.

    Torque:
    34 N*m{ 346 kgf*cm , 25 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



13. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


G039346E01
  1. Coat a new O-ring with ATF, and install it to the oil filler tube.

  1. Install the oil filler tube with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Install the oil dipstick.



14. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
  1. Install the propeller shaft with center bearing (Click here).



15. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install the front exhaust pipe (Click here).



16. INSTALL NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY


G034583E01
  1. Install the frame crossmember with the 4 bolts and 4 nuts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



17. ADJUST SHIFT LEVER POSITION


G034515E02
  1. Move the shift lever to N.

  1. Remove the nut and disconnect the control cable.



    D028682E01
  1. Turn the control shaft lever clockwise until it stops, and then turn it counterclockwise 2 notches to set it to the N position.

  1. While holding the control shaft lever slightly toward the R position side, connect the cable with the nut.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }



18. ADD AUTOMATIC TRANSMISSION FLUID

Fluid type:
Toyota Genuine ATF Type T-IV



19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.



20. PERFORM INITIALIZATION

HINT:
Refer to "INTRODUCTION REPAIR INSTRUCTION-INITIALIZATION" and perform initialization.



21. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D, and moves rearward after shifting to the R.
    If the results are not as specified, inspect the park/neutral position switch and check the shift lever.



22. CHECK FOR EXHAUST GAS LEAKS


23. CHECK AUTOMATIC TRANSMISSION FLUID