Home › TRANSMISSION ยท A340F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSPECT TORQUE CONVERTER ASSEMBLY
(Click here)


2. INSTALL TORQUE CONVERTER ASSEMBLY


D025544E01
  1. Install the torque converter clutch to the automatic transmission.

  1. Using a vernier caliper and straightedge, measure dimension A between the transmission and the end surface of the drive plate.

    Standard:
    A = 22.28 mm (0.8772 in.)



    D025545E01
  1. Using a vernier caliper and straightedge, measure dimension B shown in the illustration. Check that B is greater than A.

    Standard:
    B = A + 1.00 mm (0.0394 in.) or more



3. INSTALL TRANSFER ASSEMBLY
(Click here)


4. INSTALL NO. 1 ENGINE MOUNTING INSULATOR REAR


G034260E01
  1. Install the engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }



5. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


G034259E01
  1. Install the transmission to the engine with the 5 bolts.

    Torque:
    71 N*m{ 720 kgf*cm , 53 ft.*lbf }

    NOTICE:
    1. Do not twist or apply excessive force to the automatic transaxle assembly.
    2. Check that the torque converter rotates smoothly after installation of the automatic transaxle assembly.



6. INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT


    G034258E01
  1. Hold the crankshaft pulley bolt with a wrench and install the 6 drive plate and torque converter setting bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    First install the black colored bolt and then the remaining 5 silver colored bolts.



7. INSTALL STIFFENER PLATE


G034607E01
  1. Install the No. 2 end plate.

  1. Install the No. 4 cylinder block insulator.

  1. Install the stiffener plate LH to the engine and transmission with the 4 bolts.

    Torque:
    71 N*m{ 720 kgf*cm , 53 ft.*lbf }

  1. Install the stiffener plate RH (with clamp tube) to the engine and transmission with the 4 bolts.

    Torque:
    71 N*m{ 720 kgf*cm , 53 ft.*lbf }



8. CONNECT WIRE HARNESS


9. CONNECT CONNECTOR
  1. Transmission side:
    Connect the connectors.

    1. Connect the temperature sensor connector.

    2. Connect the park/neutral position switch connector.

    3. Connect the 2 speed sensor connectors.

    4. Connect the transmission wire connector.

  1. Transfer side:
    Connect the connectors.

    1. Connect the indicator switch connector (4WD).

    2. Connect the speedometer sensor connector.

    3. Connect the indicator switch connector (L4).

    4. Connect the indicator switch connector (neutral).



10. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


G034256
  1. Install the frame crossmember with the 4 bolts and 4 nuts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Install the 4 set bolts of the engine mounting insulator.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



11. INSTALL STARTER ASSEMBLY
(Click here)


12. INSTALL TRANSMISSION CONTROL CABLE BRACKET


G034516E01
  1. Install the control cable bracket with the 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



13. CONNECT TRANSMISSION CONTROL SHIFT CABLE ASSEMBLY


G034515E01
  1. Connect the control cable with the clip.

  1. Connect the control cable with the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



14. INSTALL OIL COOLER TUBE


G034255E02
  1. Loosely install the tip of the oil cooler tube inlet to the automatic transmission by hand.

  1. Loosely install the tip of the oil cooler tube outlet to the automatic transmission by hand.

  1. Install the 3 clamps with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } for A and B
    12 N*m{ 122 kgf*cm , 9 ft.*lbf } for C



    G034851E02
  1. Using a 17mm union nut wrench, tighten the inlet and outlet tubes.

    Torque:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



15. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


G039346E01
  1. Coat a new O-ring with ATF, and install it to the oil filler tube.

  1. Install the oil filler tube to the transmission with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Install the oil level gauge.



16. INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
(Click here)


17. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
(Click here)


18. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A111834
  1. Using a vernier caliper, measure the free length of the compression spring.

    Minimum length:
    40 mm (1.57 in.)

    If the free length is less than the minimum, replace the compression spring.

  1. Install the front pipe to the pipe support.



    A111803E01
  1. Install a new gasket to the outlet pipe.

    NOTICE:
    1. Be careful with the installation direction of the gasket.
    1. Do not reuse the gasket.
    1. To ensure a proper seal, do not use the front pipe to force the gasket onto the outlet pipe.

    HINT:
    Using a plastic-faced hammer, uniformly strike the gasket so that the gasket and outlet pipe are properly fit.

  1. Install the front pipe with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



19. INSTALL TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY


C234783
  1. Install the transfer shift lever to the shift lever retainer.

    HINT:
    Apply MP grease to the tip of the transfer shift lever.

  1. Using needle-nose pliers, install the snap ring.



20. INSTALL SHIFT LEVER BOOT ASSEMBLY
  1. Install the shift lever boot with the 4 screws.



21. ADD AUTOMATIC TRANSMISSION FLUID


22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



23. INSPECT AND ADJUST SHIFT LEVER POSITION
(Click here)


24. INSTALL CONSOLE BOX ASSEMBLY


B278048E01
  1. Install the console box with the 4 screws and 2 bolts.

  1. Install the 2 clips.
    Text in Illustration 
    *1
    Screw
    *2
    Bolt
    *3
    Clip



25. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


  1. for Manual Transmission:



    1. Attach the 12 claws to install the upper console panel.


      B277219E01


      Text in Illustration 
      *A
      for 2WD
      *B
      for 4WD



  1. for Automatic Transmission:
    Attach the 12 claws to install the upper console panel.


    B277220E01


    Text in Illustration 
    *A
    for 2WD
    *B
    for 4WD



26. INSTALL PARKING BRAKE HOLE COVER
  1. Attach the 4 claws to install the parking brake hole cover.



27. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


B277222
  1. Install the shift lever knob and twist it in the direction indicated by the arrow.



28. CHECK FOR EXHAUST GAS LEAKS
If gas is leaking, tighten the problem areas to stop the leak. Replace damaged parts as necessary.


29. INSPECT AUTOMATIC TRANSMISSION FLUID LEVEL
(Click here)


30. INSTALL NO. 2 ENGINE UNDER COVER
  1. Install the under cover with the 4 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



31. INSTALL NO. 1 ENGINE UNDER COVER
  1. Install the under cover with the 8 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }