Home › SUSPENSION & AXLE › AXLE › STEERING KNUCKLE

STEERING KNUCKLE > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL FRONT AXLE HUB ASSEMBLY


F042759E01
  1. Apply MP grease to a new O-ring.

  1. Install the O-ring to the axle hub.

  1. Install the dust cover and axle hub to the steering knuckle with the 4 bolts.

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }



2. INSTALL FRONT AXLE HUB DUST SEAL (for 4WD)


F042767E01
  1. Using SST and a press, press in a new dust seal.

    SST
    09527-17011  
    09950-70010   (09951-07100)
    09951-01000  



3. INSTALL KNUCKLE GREASE RETAINER CAP LH (for Pre-Runner)


F042765E01
  1. Using a brass bar and hammer, install a new retainer cap.

    NOTICE:
    Do not damage the retainer cap.



4. CONNECT FRONT SUSPENSION UPPER ARM ASSEMBLY LH


F043605E01
  1. Connect the upper arm with the nut.

    Torque:
    110 N*m{ 1,122 kgf*cm , 81 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.



5. CONNECT FRONT SUSPENSION LOWER ARM ASSEMBLY WITH ATTACHMENT LH


F050870E01
  1. Connect the suspension arm with the 2 bolts.

    Torque:
    160 N*m{ 1,632 kgf*cm , 118 ft.*lbf }



6. CONNECT TIE ROD END SUB-ASSEMBLY LH


C113718
  1. Connect the tie rod end with the nut.

    Torque:
    91 N*m{ 928 kgf*cm , 67 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.



7. CONNECT FRONT STABILIZER LINK ASSEMBLY LH


C099158E01
  1. Connect the stabilizer link with the nut.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud.



8. INSTALL FRONT AXLE HUB NUT (for 4WD)


F042732E01
  1. Install the hub nut.

    Torque:
    235 N*m{ 2,396 kgf*cm , 173 ft.*lbf }

  1. Install the lock cap and a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.



9. INSTALL FRONT AXLE HUB GREASE CAP (for 4WD)
  1. Install a new grease cap to the axle hub.



10. INSTALL FRONT DISC


11. INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH


F050211E01
  1. Install the disc brake cylinder with the 2 bolts.

    Torque:
    123 N*m{ 1,254 kgf*cm , 91 ft.*lbf }



    F042731E01
  1. Connect the brake tube bracket to the steering knuckle with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



    F051151E01
  1. Using SST, connect the brake tube to the disc brake cylinder.

    SST
    09023-00101  

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf } for use without SST
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } for use with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).



12. INSTALL FRONT SPEED SENSOR LH (w/ ABS)


C113715
  1. Install the speed sensor with the bolt.

  1. Connect the 2 clamps.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Connect the speed sensor wire harness to the steering knuckle with the bolt.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



13. BLEED AIR FROM BRAKE LINE
  1. w/ VSC:
    (Click here)

  1. w/o VSC:
    (Click here)



14. CHECK BRAKE FLUID LEVEL IN RESERVOIR
  1. Check the brake fluid level in the reservoir (Click here).



15. CHECK FOR BRAKE FLUID LEAKAGE
  1. Check for brake fluid leakage (Click here).



16. INSTALL FRONT WHEEL

Torque:
105 N*m{ 1,071 kgf*cm , 77 ft.*lbf }