TIMING BELT > INSTALLATION |
| 1. SET NO. 1 CYLINDER TO TDC / COMPRESSION |
![]() |
Using the crankshaft pulley bolt, align its groove with the timing pointer by turning the crankshaft clockwise.
![]() |
Set the timing and drive pulleys at each position.
| 2. INSTALL TIMING BELT |
![]() |
Remove any oil or water on each pulley, and keep them clean.
Install the timing belt on the crankshaft timing and timing belt idlers.
![]() |
Using SST, slightly turn the injection pump drive pulley clockwise. Hang the timing belt on the pulley, and align the timing marks of the drive pulley and timing belt case.
![]() |
Using SST, slightly turn the camshaft timing pulley clockwise. Hang the timing belt on the timing pulley, and align the timing marks of the timing pulley and timing belt case.
Check that the timing belt has tension between the injection pump drive and camshaft timing pulleys.
Install the timing belt on the No. 2 timing belt idler.
| 3. CHECK VALVE TIMING |
![]() |
Loosen the No. 1 timing belt idler bolt (A), and stretch the timing belt.
Slowly turn the crankshaft pulley 2 revolutions from TDC to TDC.
![]() |
Check that each pulley aligns with the timing marks as shown in the illustration.
If the timing marks do not align, remove the timing belt and reinstall it.
Tighten the No. 1 timing belt idler bolt (A).
| 4. INSTALL TIMING BELT GUIDE |
![]() |
Install the belt guide with the cup side facing outward.
| 5. INSTALL TIMING BELT COVER SUB-ASSEMBLY |
![]() |
Install 2 gaskets to the timing belt cover.
![]() |
Install the timing belt cover with the 11 bolts.
| 6. INSTALL CRANKSHAFT PULLEY |
Align the pulley set key with the key groove of the pulley, and slide the pulley to the crankshaft.
![]() |
Using SST, install the new pulley bolt.
| 7. INSTALL VANE PUMP DRIVE PULLEY |
![]() |
w/o Air Conditioning System:
Install the vane pump drive pulley and vane pump pulley spacer with the 4 bolts.
w/ Air Conditioning System:
Install the vane pump drive and No. 2 crankshaft pulleys with the 4 bolts.
| 8. INSTALL COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System) |
Temporarily install the compressor mounting bracket with the 4 bolts.
![]() |
Using several steps, uniformly install and tighten the 4 bolts.
![]() |
Temporarily install the spacer with the bolt.
| 9. INSTALL COMPRESSOR AND MAGNET CLUTCH (w/ Air Conditioning System) |
![]() |
Install the compressor with the 4 bolts.
| 10. INSTALL FAN & GENERATOR V BELT (w/ Air Conditioning System) |
![]() |
Install the V belt.
Tightening bolt C, adjust the deflection of the V belt .
Tighten the bolts A and B.
Recheck the deflection of the V belt.
| 11. INSTALL FAN & GENERATOR V BELT (w/o Air Conditioning System) |
![]() |
Install the V belt.
Using a bar, adjust the tension of the V belt.
Tighten the bolts A and B.
Check the deflection of the V belt .
| 12. INSTALL COOLER COMPRESSOR V BELT (w/ Air Conditioning System) |
![]() |
Install the V belt.
Tightening bolt B, adjust the deflection of the V belt .
Tighten nut A.
Recheck the deflection of the V belt.
| 13. INSTALL VANE PUMP V BELT |
![]() |
Install the V belt.
Using a bar, adjust the deflection of the V belt .
Tighten bolt A and nut B.
Recheck the deflection of the V belt.
| 14. INSTALL FAN SHROUD |
![]() |
Install the fan pulley to the water pump.
Install the shroud together with the coupling fan between the radiator and engine.
Install the fluid coupling fan to the fan pulley with the 4 nuts.
Attach the shroud's claws to the radiator as shown in A in the illustration.
Install the shroud with the 2 bolts.
Install the fan and generator V belt, cooler compressor V belt and vane pump V belt (Click here).
Tighten the 4 nuts of the fluid coupling fan.
![]() |
Install the radiator reservoir with the bolt.
Connect the No. 1 and No. 2 water by-pass hoses to the tank upper and lower.
![]() |
Install the oil reservoir with the 3 bolts.
| 15. CONNECT RADIATOR HOSE INLET |
| 16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 17. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
![]() |
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's FULL line.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the LOW line, add TOYOTA SLLC to the FULL line.
Install the radiator reservoir cap.
![]() |
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2,500 to 3,000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
After the coolant cools down, check that the coolant level is at the FULL line.
If the coolant level is below the LOW line, add TOYOTA SLLC to the FULL line.
| 18. INSPECT FOR COOLANT LEAK |
Check for engine coolant leaks .
| 19. CHECK IDLE ENGINE SPEED |
Warm up the engine.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Measure the idle speed.
When not using the intelligent tester:
![]() |
Using SST, connect the tachometer test probe to terminal 9 (TAC) of the DLC3.
Measure the idle speed.
| 20. CHECK MAXIMUM ENGINE SPEED |
Start the engine.
Fully depress the accelerator pedal.
Measure the maximum speed.