Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)

AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio receiver assembly.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.
If there is a short in the circuit, the same condition as when the switch is continuously depressed occurs.
Therefore, the radio receiver assembly cannot be operated using the steering pad switch assembly, and the radio receiver assembly itself cannot function.

WIRING DIAGRAM


C240167E10


INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the SRS (Click here).

1.INSPECT STEERING PAD SWITCH ASSEMBLY


  1. Remove the steering pad switch assembly (Click here).


    C237717E06


    Text in Illustration 
    *A
    w/ Multi-information Display
    -
    -
    *1
    Volume+ Switch
    *2
    Volume- Switch
    *3
    Seek- Switch
    *4
    Seek+ Switch
    *5
    MODE Switch
    -
    -

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    10 (AU1) - 8 (EAU)
    No switch is pushed
    95 to 105 kΩ
    Seek+ switch is pushed
    Below 2.5 Ω
    Seek- switch is pushed
    312.6 to 345.5 Ω
    Volume+ switch is pushed
    950 to 1050 Ω
    Volume- switch is pushed
    2954.5 to 3265.5 Ω
    9 (AU2) - 8 (EAU)
    No switch is pushed
    95 to 105 kΩ
    MODE switch is pushed
    Below 2.5 Ω



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


2.INSPECT SPIRAL CABLE SUB-ASSEMBLY


    C237983E01
  1. Remove the spiral cable sub-assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    8 (EAU) - 4 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    10 (AU1) - 6 (AU1)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    9 (AU2) - 5 (AU2)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    Text in Illustration 
    *a
    Steering Pad Switch Side
    *b
    Vehicle Side

    CAUTION:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS (Click here).



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - SPIRAL CABLE)
  1. Disconnect the R27 radio receiver assembly connector.

  1. Disconnect the S30 spiral cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R27-21 (SW1) - S30-6 (AU1)
    Always
    Below 1 Ω
    R27-22 (SW2) - S30-5 (AU2)
    R27-23 (SWG) - S30-4 (EAU)
    R27-21 (SW1) - Body ground
    Always
    10 kΩ or higher
    R27-22 (SW2) - Body ground
    R27-23 (SWG) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)