ENGINE ASSEMBLY > INSTALLATION |
| 1. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH |
Install the front No. 1 engine mounting bracket with the 4 bolts.
| 2. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH |
Install the front No. 1 engine mounting bracket with the 4 bolts.
| 3. INSTALL ENGINE COOLANT TEMPERATURE SENSOR |
Install a new gasket to the engine coolant temperature sensor.
Install the engine coolant temperature sensor.
Connect the engine coolant temperature sensor connector.
| 4. INSTALL CAMSHAFT POSITION SENSOR |
Apply a light coat of engine oil to the O-ring of the camshaft position sensor.
Install the camshaft position sensor with the bolt.
Connect the camshaft position sensor connector.
| 5. INSTALL CRANKSHAFT POSITION SENSOR |
Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.
Install the crankshaft position sensor with the bolt.
Attach the 4 clips and connect the crankshaft position sensor connector.
| 6. INSTALL VANE PUMP ASSEMBLY |
Install a new O-ring to the vane pump.
Install the vane pump with the 2 nuts.
| 7. INSTALL VACUUM PUMP ASSEMBLY |
Install 2 new O-rings to the vacuum pump.
Install the vacuum pump with the 2 nuts.
| 8. INSTALL OIL COOLER COVER SUB-ASSEMBLY |
Install a new gasket and the oil cooler cover with the 13 bolts.
Connect the No. 2 vacuum transmitting pipe with the 2 nuts.
Connect the oil pressure switch connector.
| 9. INSTALL FUEL SUPPLY PUMP ASSEMBLY |
![]() |
Check that the injection gear in the timing gear case moves back and forth smoothly.
Install a new O-ring to the fuel supply pump.
Apply a light coat of engine oil to the O-ring.
![]() |
Align the groove of the injection gear with the set key on the drive shaft.
Install the fuel supply pump with the 2 nuts.
Install a new O-ring.
![]() |
Using SST, hold the crankshaft pulley and install the set nut.
Install the pump drive shaft pulley and No. 2 camshaft timing pulley flange with the 4 bolts.
![]() |
Move the pump drive shaft pulley back and forth to check the thrust clearance of the injection pump drive shaft.
Connect the fuel temperature sensor connector and suction control valve connector.
Connect the 2 fuel hoses.
| 10. INSTALL COMMON RAIL ASSEMBLY |
Install the common rail and No. 2 intake manifold insulator with the 2 bolts.
Connect the 2 connectors.
| 11. INSTALL OIL FILTER SUB-ASSEMBLY |
Check and clean the oil filter installation surface.
Apply clean engine oil to the gasket of a new oil filter.
Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.
![]() |
Using SST, tighten the oil filter. Depending on the space available, choose from the following.
If enough space is available, use a torque wrench to tighten the oil filter.
If enough space is not available to use a torque wrench, tighten the oil filter 3/4 of a turn by hand or with a common wrench.
| 12. INSTALL FUEL INLET PIPE SUB-ASSEMBLY |
Temporarily install the fuel inlet pipe with the union nuts.
Using a 17 mm union nut wrench, tighten the fuel inlet pipe union nut on the common rail side.
Using a 17 mm union nut wrench, tighten the fuel inlet pipe union nut on the fuel supply pump side.
| 13. INSTALL GLOW PLUG ASSEMBLY |
| 14. INSTALL INTAKE MANIFOLD |
| 15. INSTALL DIESEL THROTTLE BODY ASSEMBLY |
Install a new gasket and the diesel throttle body with the 2 bolts and 2 nuts.
Connect the 2 connectors.
| 16. INSTALL WATER OUTLET |
![]() |
Install a new gasket to the cylinder head as shown in the illustration.
| *1 | Claw |
Install the water outlet with the 2 bolts.
| 17. INSTALL THERMOSTAT |
![]() |
Install a new gasket to the thermostat.
| *1 | Gasket |
| *2 | Jiggle Valve |
| *a | CORRECT |
| *b | INCORRECT |
![]() | Upward |
Insert the thermostat into the cylinder block with the jiggle valve facing straight upward.
| 18. INSTALL WATER INLET |
Install the wire harness clamp bracket to the water inlet with the bolt.
Install the water inlet with the 3 bolts.
Connect the wire harness clamp.
| 19. INSTALL EXHAUST MANIFOLD |
Temporarily install a new gasket, the exhaust manifold, 8 new collars and the 8 plate washers to the cylinder head with 8 new nuts.
![]() |
Tighten the 8 nuts in the order shown in the illustration.
| 20. INSTALL TURBOCHARGER SUB-ASSEMBLY |
| 21. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET |
Install the No. 1 compressor mounting bracket with the 4 bolts.
| 22. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Install the V-ribbed belt tensioner with the 4 bolts.
| *1 | Cylinder Block |
| *2 | V-ribbed Belt Tensioner |
| 23. INSTALL GENERATOR BRACKET |
Install the generator bracket with the bolt.
| 24. INSTALL GENERATOR ASSEMBLY |
![]() |
Install the generator and with the 2 bolts.
Install the generator wire with the nut.
Connect the generator connector.
| 25. INSTALL NO. 2 IDLE PULLEY ASSEMBLY |
Install the spacer, No. 2 idle pulley and pulley plate with the bolt.
| 26. INSTALL NO. 1 INTERCOOLER SUPPORT BRACKET |
Install the No. 1 intercooler support bracket with the 2 bolts.
| 27. INSTALL NO. 2 INTERCOOLER SUPPORT BRACKET |
Install the No. 2 intercooler support bracket with the 2 bolts.
| 28. INSTALL CRANKSHAFT PULLEY |
Align the keyway of the pulley with the key located on the crankshaft, and then slide the pulley into place to install it.
![]() |
Using SST, install the pulley bolt.
| 29. INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY |
Using a 10 mm hexagon wrench, install a new washer and the No. 1 timing belt idler with the bolt.
Check that the idler pulley moves smoothly.
If the idler pulley does not move smoothly, check the installation condition of the idler and washer.
| 30. INSTALL TIMING BELT |
![]() |
Check that the timing marks are aligned as shown in the illustration.
| *1 | Timing Mark |
Install the timing belt to the pump drive shaft pulley, camshaft timing pulley and No. 1 timing belt idler in sequence.
![]() |
Place the tensioner upright. Then set a press on the top of the tensioner.
Using the press, slowly push in the push rod using 981 to 9800 N (100 to 999 kgf, 220 to 2203 lbf) of force.
Align the holes of the push rod and housing. Then pass a 1.5 mm hexagon wrench through the holes to fix the push rod in place.
Temporarily install the timing belt tensioner with the 2 bolts while pushing the idler pulley toward the timing belt.
Tighten the 2 bolts.
![]() |
Remove the 1.5 mm hexagon wrench from the tensioner.
![]() |
Turn the crankshaft clockwise 720° and check that the timing marks are aligned as shown in the illustration.
| *1 | Timing Mark |
| 31. INSTALL NO. 1 TIMING BELT COVER |
Install the timing belt cover and 6 washers with the 6 bolts.
| 32. INSTALL FRONT ENGINE MOUNTING INSULATOR |
Install the 2 front engine mounting insulators with the 2 nuts.
| 33. INSTALL ENGINE WIRE |
Install the engine wire to the engine.
| 34. INSTALL ENGINE HANGERS |
![]() |
Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
| No. 1 Engine Hanger | 12284-30060 or 12284-30070 |
| No. 2 Engine Hanger | 12282-67030 |
| Bolt | 91552-81014 and 91642-81030 |
| 35. REMOVE ENGINE FROM ENGINE STAND |
Attach an engine sling device and hang the engine with a chain block.
Remove the engine from the engine stand.
| 36. INSTALL ENGINE ASSEMBLY |
Slowly lower the engine into the engine compartment.
Install the engine with the 4 bolts and 4 nuts.
Remove the 2 bolts and 2 engine hangers.
| 37. INSTALL REAR END PLATE |
Install the rear end plate with the bolt.
| 38. INSTALL FLYWHEEL SUB-ASSEMBLY |
Clean the bolts and their holes.
Apply adhesive to 2 or 3 threads at the end of each bolt.
![]() |
Using SST, hold the crankshaft pulley.
Install the flywheel to the crankshaft.
![]() |
Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.
| 39. INSTALL CLUTCH DISC ASSEMBLY |
![]() |
Insert SST into the clutch disc. Then insert SST (together with the clutch disc) into the flywheel.
| 40. INSTALL CLUTCH COVER ASSEMBLY |
![]() |
Align the matchmarks on the clutch cover and flywheel.
Loosely install the 6 bolts.
Tighten the 6 bolts as described below.
Determine the first bolt to be tightened by choosing the bolt closest to the knock pin.
Uniformly tighten the 6 bolts in diametrically opposite pairs relative to the position of the first bolt. Use the illustration as a reference.
Lightly move SST up and down, and right and left.
Check that the disc is in the center, and then tighten the bolts.
| 41. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY |
![]() |
Using a dial indicator with roller instrument, measure the diaphragm spring tip alignment.
![]() |
| 42. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR |
Install the 4 bolts and rear No. 1 engine mounting insulator.
| 43. INSTALL MANUAL TRANSMISSION ASSEMBLY |
| 44. CONNECT COOLER COMPRESSOR ASSEMBLY |
Connect the cooler compressor with the 4 bolts.
| 45. CONNECT WIRE HARNESS |
Connect the 4 ECM connectors.
Connect the turbo motor driver connector.
Connect the 3 injector driver connectors.
Attach the clamp and connect the wire harness with the 2 nuts.
Connect the ground cable with the bolt.
Connect the 2 engine room junction block connectors.
Connect the engine room junction block wire with the nut.
Install the side engine room relay block cover.
Install the upper relay block cover.
| 46. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Attach the 2 hinges to install the glove compartment door.
| *1 | Hinge |
![]() |
While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.
| *1 | Stopper |
| 47. CONNECT UNION TO CONNECTOR TUBE HOSE |
Connect the union to connector tube hose.
| 48. CONNECT FUEL HOSE |
Connect the 2 fuel hoses.
| 49. CONNECT PRESSURE FEED TUBE ASSEMBLY |
Connect the pressure feed tube.
Connect the oil reservoir to pump hose.
| 50. CONNECT HEATER HOSE |
Connect the 2 heater hoses.
| 51. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY |
| 52. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
| 53. INSTALL STARTER ASSEMBLY |
| 54. INSTALL RADIATOR ASSEMBLY |
| 55. INSTALL INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR |
| 56. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY |
Install the engine cover with the 3 bolts and 2 cap nuts.
| 57. INSTALL AIR CLEANER ASSEMBLY |
Connect the air cleaner hose.
Install the cleaner with the 2 bolts.
Tighten the hose clamp.
Connect the connector to the mass air flow meter connector.
| 58. INSTALL BATTERY TRAY |
| 59. INSTALL BATTERY |
| 60. INSTALL BATTERY CLAMP SUB-ASSEMBLY |
Install the battery clamp with the bolt and nut.
| 61. ADD POWER STEERING FLUID |
| 62. ADD TRANSMISSION OIL |
![]() |
| 63. ADD ENGINE OIL |
Add new engine oil.
| Oil Grade | Oil Viscosity (SAE) |
| G-DLD1, API CF-4 or CF (You may also use API CE or CD) | - 5W-30 - 10W-30 - 15W-40 - 20W-50 |
| Item | Specified Condition |
| Drain and refill without oil filter change | 6.6 liters (7.0 US qts, 5.8 Imp. qts) |
| Drain and refill with oil filter change | 6.9 liters (7.3 US qts, 6.1 Imp. qts) |
| Dry fill | 7.4 liters (7.8 US qts, 6.5 Imp. qts) |
Install the oil filler cap.
| 64. INSTALL HOOD SUB-ASSEMBLY |
Install the hood with the 4 bolts.
Connect the washer nozzle hose.
Adjust the hood (Click here).
| 65. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 66. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Check if the engine starts.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
![]() |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2
| *a | Reference (Active Test Operation) |
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
| 67. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the B line of the radiator reservoir.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
After the coolant cools down, check that the coolant level is at the F line.
If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 68. BLEED AIR FROM POWER STEERING SYSTEM |
Check the fluid level.
Jack up the front of the vehicle and support it with stands.
Turn the steering wheel.
With the engine stopped, turn the steering wheel slowly from lock to lock several times.
Lower the vehicle.
Start the engine. Run the engine at idle for a few minutes.
Turn the steering wheel.
With the engine idling, turn the steering wheel to the left or right full lock position and hold it there for 2 to 3 seconds. Then turn the steering wheel to the opposite full lock position and hold it there for 2 to 3 seconds.
Repeat the step above several times.
Stop the engine.
![]() |
Check for foaming or emulsification. If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.
Check the fluid level.
| 69. INSPECT POWER STEERING FLUID LEVEL |
![]() |
Keep the vehicle level.
With the engine stopped, check the power steering fluid level in the oil reservoir. If necessary, add power steering fluid.
Start the engine and run it at idle.
Turn the steering wheel to the left or right full lock position, and then turn the steering wheel to the opposite full lock position. Repeat this several times to raise fluid temperature.
![]() |
Check for foaming or emulsification. If foaming or emulsification is identified, bleed air from the power steering system.
![]() |
With the engine idling, measure the fluid level in the oil reservoir.
Stop the engine.
Wait a few minutes and remeasure the fluid level in the oil reservoir.
Check the fluid level.
| 70. PERFORM REGISTRATION |
Perform registration of the injector compensation codes .
Perform pilot quantity learning .
| 71. INSPECT FOR COOLANT LEAK |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 72. INSPECT FOR OIL LEAK |
Start the engine. Make sure that there are no oil leaks from the areas that were worked on.
| 73. INSPECT FOR EXHAUST GAS LEAK |
| 74. INSPECT FOR FUEL LEAK |
Check that there are no leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.
Start the engine and check that there are no leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.
Disconnect the return hose from the common rail.
Start the engine and check for fuel leaks from the return pipe.
If there is fuel leakage, replace the common rail.
Connect the intelligent tester to the DLC3.
Start the engine and push the intelligent tester main switch on.
Select the Fuel Leak test from the Active Test mode on the intelligent tester.
If the intelligent tester is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.
Check that there are no leaks from any part of the fuel system.
Reconnect the return hose to the common rail.
| 75. CHECK ENGINE IDLE SPEED AND MAXIMUM SPEED |
Connect the intelligent tester to the DLC3.
![]() |
If a tester is not available, connect the tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.
| *a | Front view of DLC3 |
Inspect the idle speed.
Start the engine and measure the idle speed.
Inspect the maximum speed.
Start the engine.
Fully depress the accelerator pedal.
Measure the maximum speed.
If the tester probe of a tachometer is connected to the DLC3, disconnect the tester probe together with SST from terminal 9 of the DLC3.
Disconnect the intelligent tester from the DLC3.
| 76. INSPECT ENGINE OIL LEVEL |
Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.
If low, check for leakage and add oil up to the full level mark.
| 77. INSTALL NO. 2 ENGINE UNDER COVER |
| 78. INSTALL NO. 1 ENGINE UNDER COVER |