OIL PUMP > INSTALLATION |
| 1. INSTALL TIMING GEAR CASE ASSEMBLY |
![]() |
Install 2 new O-rings to the cylinder block.
Remove any old seal packing (FIPG material) from the timing gear case and cylinder block.
Set a new gasket to the timing gear case.
![]() |
Apply seal packing to the areas shown in the illustration.
![]() |
Align the "2" timing marks of the No. 1 balance shaft driven gear and oil pump drive gear, and install the timing gear case to the cylinder block.
Install the timing gear case with the 8 bolts and union bolt.
Make sure that the oil pump drive gear rotates smoothly.
| 2. INSTALL OIL STRAINER SUB-ASSEMBLY |
Install a new gasket and the oil strainer with the 2 bolts and nut.
| 3. INSTALL OIL PAN SUB-ASSEMBLY |
Remove any old seal packing (FIPG) from the oil pan and cylinder block.
![]() |
Apply seal packing to the areas shown in the illustration.
Install the oil pan with the 22 bolts and 2 nuts.
| 4. INSTALL FUEL SUPPLY PUMP ASSEMBLY |
![]() |
Check that the supply pump gear in the timing gear case moves back and forth smoothly.
Install a new O-ring to the pump.
Apply a light coat of engine oil to the O-ring.
![]() |
Align the set key on the drive shaft with the groove of the injection gear.
![]() |
Install the pump with the 2 nuts.
Set a new O-ring before installing the set nut.
![]() |
Using SST, hold the crankshaft pulley and install the set nut.
![]() |
Move the pump drive shaft pulley back and forth to check the thrust clearance of the injection pump drive shaft.
![]() |
Connect the 2 connectors.
![]() |
Connect the 2 fuel hoses.
![]() |
Temporarily install the fuel inlet pipe with the union nuts.
Using union nut wrench, tighten the injection pipe union nut on the common rail side.
Using union nut wrench, tighten the injection pipe union nut on the supply pump side.
Install the oil dipstick guide with the bolt.
![]() |
Install the clamp with the bolt.
| 5. INSTALL INJECTION GEAR |
![]() |
Align the "3" timing marks of the injection gear and balance No. 2 shaft driven gear, and install the injection gear.
Set a new O-ring and then temporarily install the nut. Using your hand, check the thrust clearance of the supply pump drive shaft by driving the injection gear.
| 6. INSTALL CRANKSHAFT TIMING GEAR |
![]() |
Align the "1" timing marks of the oil pump drive gear and crankshaft timing gear as shown in the illustration.
Using SST, install the crankshaft timing gear.
| 7. INSTALL NO. 1 IDLE GEAR |
![]() |
Install the No. 1 idle gear shaft to the cylinder block.
![]() |
Align the "4" timing marks of the No. 1 idle gear and injection gear, as shown in the illustration.
Align the "5" timing marks of the No. 1 idle gear and crankshaft timing gear, and install the No. 1 idle gear, as shown in the illustration.
Install the idle gear thrust plate with the 2 bolts.
Remove the service bolt.
Install the No. 1 crankshaft sensor plate.
| 8. INSTALL TIMING GEAR COVER |
![]() |
Install a new O-ring to the timing gear case.
Remove any old seal packing (FIPG material) from the timing gear cover.
![]() |
Apply seal packing to the areas shown in the illustration.
Install the cover with the 14 bolts and 2 nuts.
Install the No. 1 vacuum transmitting pipe with the bolt.
| 9. INSTALL CRANKSHAFT POSITION SENSOR |
Install the crankshaft position sensor with the bolt.
| 10. INSTALL CAMSHAFT POSITION SENSOR |
Install the camshaft position sensor with the bolt.
| 11. INSTALL CRANKSHAFT PULLEY |
![]() |
Align the pulley set key with the key groove of the pulley and install the pulley.
Using SST, install the pulley bolt.
| 12. INSTALL PUMP DRIVE SHAFT PULLEY |
Install a new O-ring to the supply pump.
Temporarily install the supply pump with the nut.
![]() |
Using SST, hold the crankshaft pulley and tighten the nut.
![]() |
Install the No. 2 camshaft timing pulley flange and pump drive shaft pulley with the 4 bolts.
![]() |
Using a dial indicator, check the thrust clearance of the pump drive shaft while moving the pump drive shaft pulley back and forth.
| 13. INSTALL VANE PUMP ASSEMBLY |
Install a new O-ring to the vane pump.
Install the vane pump with the 2 nuts.
| 14. INSTALL VACUUM PUMP ASSEMBLY |
Install 2 new O-rings to the vacuum pump.
Install the vacuum pump with the 2 nuts.
| 15. INSTALL WATER PUMP ASSEMBLY |
![]() |
Install a new gasket and the water pump with the 5 bolts and 2 nuts.
| 16. INSTALL NO. 2 TIMING BELT COVER |
![]() |
Apply seal packing (FIPG) to the specified areas shown in the illustration.
Install the No. 2 timing belt cover with the 4 bolts and nut.
| 17. INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY |
Install the timing belt idler and a new spacer with the bolt.
| 18. INSTALL CAMSHAFT TIMING PULLEY |
![]() |
Install the camshaft timing pulley.
Fasten the bolt of the camshaft timing pulley by holding the camshaft with a wrench.
| 19. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Install 4 new No. 3 cylinder head cover gaskets to the cylinder head cover in the directions shown in the illustration.
Remove any old seal packing (FIPG) material from the cylinder head.
![]() |
Apply seal packing to the specific areas shown in the illustration.
Install a new cylinder head cover gasket and the cylinder head cover with the 10 bolts and 2 nuts.
Install 4 new nozzle holder seals.
Connect the ventilation hose.
Connect the 4 connectors and install the 3 bolts.
| 20. INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY |
Temporarily install the No. 4 injection pipe with the union nuts.
Install the 2 bolts.
![]() |
Using a 17 mm union nut wrench, tighten the injection pipe union nut on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
| 21. INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY |
Temporarily install the No. 1, No. 2 and No. 3 injection pipes with the union nuts.
![]() |
Install the No. 2 and No. 3 injection pipe clamps with the bolt and 2 nuts, as shown in the illustration.
![]() |
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
| 22. INSTALL FUEL INLET PIPE SUB-ASSEMBLY |
![]() |
Temporarily install the fuel inlet pipe with the union nuts.
Using a 17 mm union nut wrench, tighten the fuel inlet pipe union nut on the common rail side.
Using a 17 mm union nut wrench, tighten the fuel inlet pipe union nut on the supply pump side.
Install a new O-ring to the engine oil level dipstick guide.
Install the engine oil level dipstick guide with the bolt.
Install the clamp with the bolt.
Install the engine oil level dipstick.
| 23. INSTALL MANIFOLD STAY |
![]() |
Install the stay with the 2 bolts.
| 24. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET |
Install the No. 1 compressor mounting bracket with the 4 bolts.
| 25. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Install the V-ribbed belt tensioner with the 4 bolts.
| 26. INSTALL GENERATOR BRACKET |
Install the generator bracket with the bolt.
| 27. INSTALL GENERATOR ASSEMBLY |
![]() |
Install the generator with the 2 bolts.
Install the generator wire with the nut.
Install the terminal cap.
Connect the generator connector.
| 28. INSTALL NO. 2 IDLE PULLEY ASSEMBLY |
Install the spacer, No. 2 idle pulley and pulley plate with the bolt.
| 29. INSTALL TIMING BELT |
![]() |
Check that the timing marks are aligned as shown in the illustration.
Using a 10 mm hexagon wrench, install the timing belt idler pulley and new washer with the bolt.
Check that the idler pulley moves smoothly.
If it does not move smoothly, check the idler sub-assembly and washer.
Install the timing belt to the pump drive shaft pulley, camshaft timing pulley and No. 1 timing belt idler in sequence.
![]() |
Place the tensioner upright. Then set a press to the top of the tensioner.
Using the press, slowly push in the push rod using 981 to 9,807 N (100 to 1,000 kgf, 220 to 2,205 lbf) of force.
Align the holes of the push rod and housing. Then pass a 1.5 mm hexagon wrench through the holes to keep the setting position of the push rod.
Install the timing belt tensioner with the 2 bolts while pushing the idler pulley toward the timing belt.
Tighten the 2 bolts.
![]() |
Remove the 1.5 mm hexagon wrench from the tensioner.
![]() |
Turn the crankshaft clockwise 720° and check that the timing marks are aligned as shown in the illustration.
| 30. INSTALL NO. 1 TIMING BELT COVER |
Install the timing belt cover with the 6 bolts.
Install the wire harness clamp.
Install the water hose clamp with the bolt.
| 31. INSTALL ENGINE ASSEMBLY |
| 32. ADD ENGINE OIL |
Wipe the oil pan and drain plug.
Install a new gasket and the drain plug.
Add new oil.
| Item | Specified Condition |
| Drain and refill with oil filter change | 6.9 liters (7.3 US qts, 6.1 Imp. qts) |
| Drain and refill without oil filter change | 6.6 liters (7.0 US qts, 5.8 Imp. qts) |
| Dry fill | 7.4 liters (7.8 US qts, 6.5 Imp. qts) |
Install the oil filler cap.
| 33. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 34. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
![]() |
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.
| Item | Specified Condition |
| Manual transmission | 9.8 liters (10.4 US qts, 8.6 Imp. qts) |
| Automatic transmission | 11.1 liters (11.7 US qts, 9.8 Imp. qts) |
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
![]() |
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2,500 to 3,000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
After the coolant cools down, check that the coolant level is at the F line.
If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 35. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Start the engine.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
![]() |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
| 36. BLEED AIR FROM POWER STEERING SYSTEM |
Check the fluid level.
Jack up the front of the vehicle and support it with stands.
Turn the steering wheel.
With the engine stopped, turn the steering wheel slowly from lock to lock several times.
Lower the vehicle.
Start the engine. Run the engine at idle for a few minutes.
Turn the steering wheel.
With the engine idling, turn the steering wheel to the left or right full lock position and hold it there for 2 to 3 seconds. Then turn the steering wheel to the opposite full lock position and hold it there for 2 to 3 seconds.
Repeat the step above several times.
Stop the engine.
![]() |
Check for foaming or emulsification. If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.
Check the fluid level.
| 37. INSPECT FOR POWER STEERING FLUID LEVEL |
![]() |
Keep the vehicle level.
With the engine stopped, check the power steering fluid level in the oil reservoir. If necessary, add power steering fluid.
Start the engine and run it at idle.
Turn the steering wheel to the left or right full lock position, and then turn the steering wheel to the opposite full lock position. Repeat this several times to raise fluid temperature.
![]() |
Check for foaming or emulsification. If foaming or emulsification is identified, bleed air from the power steering system.
![]() |
With the engine idling, measure the fluid level in the oil reservoir.
Stop the engine.
Wait a few minutes and remeasure the fluid level in the oil reservoir.
Check the fluid level.
| 38. PERFORM REGISTRATION |
Perform registration of the injector compensation codes .
Perform pilot quantity learning .
| 39. INSPECT FOR OIL LEAK |
| 40. INSPECT FOR COOLANT LEAK |
| 41. INSPECT EXHAUST GAS LEAK |
| 42. INSPECT FOR FUEL LEAK |
Check that there are no leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.
Start the engine and check that there are no leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.
Disconnect the return hose from the common rail.
Start the engine and check for fuel leaks from the return pipe.
If there is fuel leakage, replace the common rail.
Connect the intelligent tester to the DLC3.
Start the engine and push the intelligent tester main switch on.
Select the Fuel Leak test from the Active Test mode on the intelligent tester.
If the intelligent tester is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.
Check that there are no leaks from any part of the fuel system.
Reconnect the return hose to the common rail.
| 43. INSPECT ENGINE OIL LEVEL |
Warm up the engine, stop the engine and wait for 5 minutes. The oil level should be between the dipstick's low and full level marks.
If the oil level is low, check for leakage and add oil up to the full level mark.