Home › STEERING › POWER STEERING › STEERING GEAR

STEERING GEAR > INSTALLATION

for Preparation Click here



1. INSTALL POWER STEERING LINK ASSEMBLY


    G100902
  1. Install the steering link with the 2 bolts and 2 nuts.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

    HINT:
    If necessary, return the differential to its original position and install the differential mount.



2. INSTALL FRONT STABILIZER BAR FRONT
  1. Install the front stabilizer bar to the vehicle body.



3. STABILIZE SUSPENSION


4. CONNECT STEERING GEAR OUTLET RETURN TUBE


    G100926E02
  1. Using union nut wrench, connect the outlet return tube.

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



    G100900
  1. Install the hose with the clip.



5. CONNECT PRESSURE FEED TUBE ASSEMBLY


    G100899
  1. Install the pressure feed tube to the steering link with the bolt.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



    C178048E02
  1. Using union nut wrench, tighten the flare nut and connect the pressure feed tube.

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



6. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY
  1. Align the matchmarks on the steering intermediate shaft and steering link.

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



7. CONNECT STEERING SLIDING YOKE


    G035017E03
  1. Align the matchmarks on the steering sliding yoke and steering intermediate shaft, and connect the steering sliding yoke to the steering intermediate shaft.

  1. Install the bolt labeled B.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. Tighten the bolt labeled A.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



8. CONNECT TIE ROD END SUB-ASSEMBLY LH
  1. Connect the tie rod end to the steering knuckle arm with the nut.

    Torque:
    91 N*m{ 928 kgf*cm , 67 ft.*lbf }

  1. Install a new cotter pin.



9. CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



10. INSTALL FRONT SIDE MEMBER TO FRONT SUSPENSION CROSSMEMBER BRACE
  1. Install the crossmember brace with the 8 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



11. INSTALL NO. 1 ENGINE UNDER COVER
  1. Install the under cover with the 4 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



12. INSTALL NO. 2 ENGINE UNDER COVER
  1. Install the under cover with the 4 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



13. INSTALL FRONT WHEEL


14. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


15. INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    C238286E02
  1. Using pliers, pinch the clamp and attach the claw to install the combination switch assembly with spiral cable sub-assembly to the steering column assembly.

  1. Connect the connectors to the combination switch assembly with spiral cable sub-assembly.



16. INSTALL STEERING COLUMN COVER UPPER
  1. Attach the claw to install the upper cover.



17. INSTALL STEERING COLUMN COVER LOWER


    C238860
  1. Install the lower cover with the 3 screws.



18. INSTALL STEERING WHEEL ASSEMBLY


    G100880E01
  1. Align the matchmarks on the steering wheel and main shaft.

  1. Install the steering set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



19. INSPECT STEERING WHEEL CENTER POINT


20. INSTALL STEERING PAD ASSEMBLY


    B278764
  1. Support the steering pad with one hand.

  1. Connect the connector to the steering pad.

    NOTICE:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. Connect the horn connector.

  1. Confirm that the groove along the circumference of the "TORX" screw is attached to the screw case and place the steering pad onto the steering wheel.

  1. Using a T30 "TORX" socket wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


22. CHECK SRS WARNING LIGHT
(Click here)


23. ADD POWER STEERING FLUID


24. BLEED AIR FROM POWER STEERING SYSTEM
(Click here)


25. CHECK POWER STEERING FLUID LEVEL IN RESERVOIR


26. CHECK FOR POWER STEERING FLUID LEAKAGE


27. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)