DTC P0105 Manifold Absolute Pressure / Barometric Pressure Circuit |
DTC P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input |
DTC P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input |

| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| 2 seconds after engine is started, race engine for 1 second | After the engine is started, condition (a) continues for more than 2.0 seconds (1 trip detection logic): (a) Manifold absolute pressure sensor voltage is 0.1 V or less, or 4.8 V or more. |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| 2 seconds after engine is started, race engine for 1 second | After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic): (a) Manifold absolute pressure sensor voltage is 0.1 V or less. |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| 2 seconds after engine is started, race engine for 1 second | After the engine is started, condition (a) continues for more than 0.5 seconds (1 trip detection logic): (a) Manifold absolute pressure sensor voltage is 4.8 V or higher. |
|
| DTC No. | Data List |
| P0105 |
|
| P0107 | |
| P0108 |
| Intake Manifold Pressure | Malfunction |
| Approximately 0 kPa |
|
| 250 kPa (1875 mmHg, 73.8 in.Hg) or higher |
|

| 1.READ VALUE USING INTELLIGENT TESTER (MANIFOLD ABSOLUTE PRESSURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.
Read the value.
|
| ||||
|
| ||||
| 2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM) |
Disconnect the manifold absolute pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T9-2 (PIM) - E6-28 (PIM) | Always | Below 1 Ω |
| T9-3 (VC) - E7-18 (VC) | Always | Below 1 Ω |
| T9-1 (E) - E7-28 (E2) | Always | Below 1 Ω |
| T9-2 (PIM) or E6-28 (PIM) - Body ground | Always | 10 kΩ or higher |
| T9-3 (VC) or E7-18 (VC) - Body ground | Always | 10 kΩ or higher |
Reconnect the manifold absolute pressure sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL) |
![]() |
Disconnect the manifold absolute pressure sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| T9-3 (VC) - T9-1 (E) | Ignition switch ON | 4.75 to 5.25 V |
| *a | Front view of wire harness connector (to Absolute Pressure Sensor) |
Reconnect the manifold absolute pressure sensor connector.
|
| ||||
| OK | |
| 4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR |
Replace the manifold absolute pressure sensor.
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0105, P0107 OR P0108) |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the tester off.
Start the engine.
After the engine is started for 2 seconds, race the engine for 1 second.
Turn the tester on.
Confirm that the DTC is not output again.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P0105, P0107 or P0108.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL | A |
| NORMAL | B |
|
| ||||
| A | |
| 6.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 7.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the tester off.
Turn the ignition switch to ON for 3 seconds and turn the tester on.
After the engine is started for 2 seconds, race the engine for 1 second.
Confirm that the DTC is not output again.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P0105, P0107 or P0108.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, race the engine for 1 minute, and then idle the engine for 5 minutes.
| NEXT | ||
| ||