DTC P0180 Fuel Temperature Sensor "A" Circuit |
DTC P0182 Fuel Temperature Sensor "A" Circuit Low Input |
DTC P0183 Fuel Temperature Sensor "A" Circuit High Input |

| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch to ON for 0.5 seconds | Open or short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch to ON for 0.5 seconds | Short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch to ON for 0.5 seconds | Open in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
| DTC No. | Data List |
| P0180 | Fuel Temp |
| P0182 | |
| P0183 |
| Temperature Displayed | Malfunction |
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |

| 1.READ VALUE USING INTELLIGENT TESTER (FUEL TEMPERATURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temp.
Read the value.
| Result | Proceed to |
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| OK (Same as actual fuel temperature) | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
![]() |
Disconnect the fuel temperature sensor connector.
Connect terminals 2 and 1 of the fuel temperature sensor connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temp.
Read the value.
| *1 | Fuel Temperature Sensor |
| *2 | ECM |
| *A | for Manual Transmission |
| *B | for Automatic Transmission |
| *a | Front view of wire harness connector (to Fuel Temperature Sensor) |
Reconnect the fuel temperature sensor connector.
|
| ||||
| OK | |
| 3.REPLACE FUEL SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR) |
Replace the fuel supply pump assembly (Click here).
|
| ||||
| 4.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM) |
Disconnect the fuel temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F10-2 - E7-29 (THF) | Always | Below 1 Ω |
| F10-1 - E7-28 (E2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| F33-2 - E7-29 (THF) | Always | Below 1 Ω |
| F33-1 - E7-28 (E2) | Always | Below 1 Ω |
Reconnect the fuel temperature sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM. |
Replace the ECM (Click here).
|
| ||||
| 6.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) |
![]() |
Disconnect the fuel temperature sensor connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temp.
Read the value.
| *1 | Fuel Temperature Sensor |
| *2 | ECM |
Reconnect the fuel temperature sensor connector.
|
| ||||
| OK | |
| 7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR) |
Replace the fuel supply pump assembly (Click here).
|
| ||||
| 8.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM) |
Disconnect the fuel temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F10-2 or E7-29 (THF) - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel temperature sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 9.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 10.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 11.PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform fuel supply pump initialization (Click here).
|
| ||||
| 12.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch to ON for 1 second or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||