DTC P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit |
DTC P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input |
DTC P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input |
DTC P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit |
DTC P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input |
DTC P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input |
DTC P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation |

| DTC No. | DTC Detection Condition (All of following are 1 trip detection logic) | Trouble Area |
| P2120 | Condition (a) continues for 0.5 sec. or more: (a) VPA is 0.4 V or less (b) VPA is 4.8 V or more |
|
| P2122 | VPA is 0.4 V or less for 0.5 sec. or more when VPA2 output indicate accelerator pedal is opened |
|
| P2123 | Condition (a) continues for 2.0 sec. or more: (a) VPA is 4.8 V or more |
|
| P2125 | Condition (a) or (b) continues for 0.5 sec. or more: (a) VPA2 is 1.2 V or less (b) VPA2 is 4.8 V or more |
|
| P2127 | VPA2 is 1.2 V or less for 0.5 sec. or more when VPA output indicates accelerator pedal is opened |
|
| P2128 | Conditions (a) and (b) continue for 2.0 sec. or more: (a) VPA2 is 4.8 V or more (b) VPA is 0.4 V or more and VPA is 3.45 V or less |
|
| P2138 | Condition (a) or (b) continues for 2.0 sec. or more: (a) Difference between VPA and VPA2 is 0.02 V or less (b) VPA is 0.4 V or less and VPA2 is 1.2 V or less |
|

| 1.READ VALUE USING INTELLIGENT TESTER (ACCEL SENS. NO.1 VOLT % AND ACCEL SENS. NO.2 VOLT %) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.
Read the values.
| Accelerator Pedal Operation | Accel Sens. No.1 Volt % | Accel Sens. No.2 Volt % |
| Released | 10 to 22% | 24 to 40% |
| Depressed | 52 to 90% | 68 to 99% |
|
| ||||
| NG | |
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() |
Disconnect the A22 sensor connector.
Disconnect the E4 ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| VCP2 (A22-1) - VCP2 (E4-27) | Below 1 Ω |
| EPA2 (A22-2) - EPA2 (E4-29) | Below 1 Ω |
| VPA2 (A22-3) - VPA2 (E4-23) | Below 1 Ω |
| VCPA (A22-4) - VCPA (E4-26) | Below 1 Ω |
| EPA (A22-5) - EPA (E4-28) | Below 1 Ω |
| VPA (A22-6) - VPA (E4-22) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VCP2 (A22-1) or VCP2 (E4-27) - Body ground | 10 kΩ or higher |
| EPA2 (A22-2) or EPA2 (E4-29) - Body ground | 10 kΩ or higher |
| VPA2 (A22-3) or VPA2 (E4-23) - Body ground | 10 kΩ or higher |
| VCPA (A22-4) or VCPA (E4-26) - Body ground | 10 kΩ or higher |
| EPA (A22-5) or EPA (E4-28) - Body ground | 10 kΩ or higher |
| VPA (A22-6) or VPA (E4-22) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT ECM (VCPA AND VCP2 VOLTAGE) |
![]() |
Disconnect the A22 sensor APP connector.
Turn the ignition switch ON.
Measure the voltage between the terminals of the ECM connector.
| Tester Connection | Specified Condition |
| VCPA (E4-26) - EPA (E4-28) | 4.5 to 5.5 V |
| VCP2 (E4-27) - EPA2 (E4-29) |
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
Replace accelerator pedal rod assembly (Click here).
| NEXT | |
| 5.CHECK IF OUTPUT DTC RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTC.
| Display (DTC output) | Proceed to |
| P2120, P2122, P2123, P2125, P2127, P2128, or P2138 is output again | A |
| No output | B |
|
| ||||
| A | ||
| ||