Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > Air Conditioning Compressor Magnetic Clutch Circuit

for Preparation Click here


DESCRIPTION

The air conditioning amplifier assembly outputs the magnet clutch on request signal to the ECM. The ECM sends a magnet clutch on permission signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly turn the magnet clutch on based on the signal.

WIRING DIAGRAM


E229599E04


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.READ VALUE USING INTELLIGENT TESTER (A/C SIGNAL)
  1. Use the Data List to check if the magnet clutch on request signal is functioning properly (Click here).

    ECM 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/C Signal
    Magnet clutch on request signal / ON or OFF
    ON: A/C switch on
    OFF: A/C switch off
    Check this item with the engine idling and the blower switch on (LO level).

OK:
Display is as specified in normal condition.



NG
Go to step 9
OK


2.INSPECT MAGNET CLUTCH RELAY


    E170970E02
  1. Remove the magnet clutch relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE MAGNET CLUTCH RELAY
OK


3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)


    E170963E28
  1. Disconnect the A38 air conditioning amplifier assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A38-13 (MGC) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


    E225456E19
  1. Remove the air conditioning amplifier assembly with its connectors still connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A38-13 (MGC) - Body ground
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch on (magnet clutch on permitted)
    Below 1 V
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch off or on (magnet clutch not on permitted)
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Air Conditioning Amplifier Assembly)



NG
Go to step 7
OK


5.INSPECT COOLER COMPRESSOR ASSEMBLY (MAGNET CLUTCH ASSEMBLY)


    E225413
  1. Remove the cooler compressor assembly.

    1. for 1KD-FTV: Click here.
    2. for 1GR-FE: Click here.

  1. Apply battery voltage to the magnet clutch and check operation of the magnet clutch.

    OK:
    Measurement Connection
    Specified Condition
    Battery positive (+) → Terminal 1
    Battery negative (-) → Ground wire
    Magnet clutch engages

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1KD-FTV)
    B
    NG (for 1GR-FE)
    C



B
REPLACE COOLER COMPRESSOR ASSEMBLY (MAGNET CLUTCH ASSEMBLY) (Click here)

C
REPLACE COOLER COMPRESSOR ASSEMBLY (MAGNET CLUTCH ASSEMBLY) (Click here)
A


6.CHECK HARNESS AND CONNECTOR (MAGNET CLUTCH RELAY - COOLER COMPRESSOR ASSEMBLY AND BATTERY)
  1. Disconnect the A2 compressor connector.

  1. Remove the magnet clutch relay.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M1-5 - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M1-3 - A2-1
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)
  1. Disconnect the A38 air conditioning amplifier assembly connector.

  1. Disconnect the E5*1 or E13*2 ECM connector.

    1. *1: for 1KD-FTV
    2. *2: for 1GR-FE

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1KD-FTV:
    Tester Connection
    Condition
    Specified Condition
    A38-7 (ACT) - E5-19 (ACT)
    Always
    Below 1 Ω
    A38-7 (ACT) - Body ground
    Always
    10 kΩ or higher
    for 1GR-FE:
    Tester Connection
    Condition
    Specified Condition
    A38-7 (ACT) - E13-25 (ACT)
    Always
    Below 1 Ω
    A38-7 (ACT) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


    E225456E20
  1. Remove the air conditioning amplifier assembly with its connectors still connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A38-7 (ACT) - Body ground
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch on (magnet clutch on)
    11 to 14 V
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch off or on (magnet clutch off)
    Below 1 V

    Text in Illustration 
    *a
    Component with harness connected
    (Air Conditioning Amplifier Assembly)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1KD-FTV)
    B
    NG (for 1GR-FE)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM)
  1. Disconnect the A38 air conditioning amplifier assembly connector.

  1. Disconnect the E5*1 or E13*2 ECM connector.

    1. *1: for 1KD-FTV
    2. *2: for 1GR-FE

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1KD-FTV:
    Tester Connection
    Condition
    Specified Condition
    A38-21 (AC1) - E5-18 (AC1)
    Always
    Below 1 Ω
    A38-21 (AC1) - Body ground
    Always
    10 kΩ or higher
    for 1GR-FE:
    Tester Connection
    Condition
    Specified Condition
    A38-21 (AC1) - E13-24 (AC1)
    Always
    Below 1 Ω
    A38-21 (AC1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


    E225456E21
  1. Remove the air conditioning amplifier assembly with its connectors still connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A38-21 (AC1) - Body ground
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch on
    Below 1 V
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch off
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Air Conditioning Amplifier Assembly)
    Result 
    Result
    Proceed to
    NG
    A
    OK (for 1KD-FTV)
    B
    OK (for 1GR-FE)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)