Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Rear Power Window RH Manual Function does not Operate with Rear Power Window Switch RH

for Preparation Click here


DESCRIPTION

If the rear RH side manual up/down function does not operate, a malfunction may be present in the rear door window regulator sub-assembly RH, rear power window regulator switch assembly RH, power window regulator master switch assembly or wire harness.

WIRING DIAGRAM


B276859E21


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - BATTERY)


    B276367E13
  1. Disconnect the P13 rear power window regulator switch assembly RH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    P13-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Power Window Regulator Switch Assembly RH)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH


    B280844E01
  1. Remove the rear power window regulator switch assembly RH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (D) - 4 (SD)
    2 (U) - 3 (B)
    UP
    Below 1 Ω
    5 (D) - 4 (SD)
    2 (U) - 1 (SU)
    OFF
    Below 1 Ω
    5 (D) - 3 (B)
    2 (U) - 1 (SU)
    DOWN
    Below 1 Ω



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY RH)
  1. Disconnect the P13 rear power window regulator switch assembly RH connector.

  1. Disconnect the P10 rear door window regulator sub-assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P13-5 (D) - P10-1
    Always
    Below 1 Ω
    P13-2 (U) - P10-2
    Always
    Below 1 Ω
    P13-5 (D) or P10-1 - Body ground
    Always
    10 kΩ or higher
    P13-2 (U) or P10-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY RH


    B290680
  1. Remove the rear door window regulator sub-assembly RH (Click here).

  1. Apply battery voltage to connector terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 2
    Battery negative (-) → 1
    Arm of window regulator rotates counterclockwise (Up)
    Battery positive (+) → 1
    Battery negative (-) → 2
    Arm of window regulator rotates clockwise (Down)

    Text in Illustration 
    V100135
    Up
    V100136
    Down



NG
REPLACE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY RH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH)
  1. Disconnect the P6 power window regulator master switch assembly connector.

  1. Disconnect the P13 rear power window regulator switch assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P6-18 (U) - P13-1 (SU)
    Always
    Below 1 Ω
    P6-16 (D) - P13-4 (SD)
    Always
    Below 1 Ω
    P6-18 (U) or P13-1 (SU) - Body ground
    Always
    10 kΩ or higher
    P6-16 (D) or P13-4 (SD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)