DTC P0046 Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Drive the vehicle with a city driving pattern at least 10 minutes. | Either of following conditions met:
|
|

| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO P0046) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P0046 is output | A |
| P0046 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION) |
Turn the ignition switch to ON.
Turn the ignition switch off and check the DC motor operation (check the operation link movement).

|
| ||||
| OK | ||
| ||
| 3.CHECK TURBO MOTOR DRIVER |
Voltage Inspection
![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T34-3 (+B) - T34-4 (GND) | Always | 11 to 14 V |
| *a | Component with harness connected (Turbo Motor Driver) |
Output Waveform Inspection
![]() |
Turn the ignition switch to ON.
Check the waveform of the ECM connectors using an oscilloscope.
| Tester Connection | Switch Condition | Specified Condition |
| T34-2 (VNTI) - T34-4 (GND) | Ignition switch ON | Correct waveform is as shown |
| *a | Component with harness connected (Turbo Motor Driver) |
|
| ||||
| OK | |
| 4.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR RESISTANCE) |
![]() |
Disconnect the DC motor connector.
Measure the DC motor resistance.
| *a | Component without harness connected (DC Motor) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (DC MOTOR - TURBO MOTOR DRIVER) |
Disconnect the DC motor connector.
Disconnect the turbo motor driver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T34-12 (M+) - T10-2 (M+) | Always | Below 1 Ω |
| T34-5 (M-) - T10-1 (M-) | Always | Below 1 Ω |
| T34-12 (M+) or T10-2 (M+) - Body ground | Always | 10 kΩ or higher |
| T34-5 (M-) or T10-1 (M-) - Body ground | Always | 10 kΩ or higher |
Reconnect the turbo motor driver connector.
Reconnect the DC motor connector.
|
| ||||
| OK | |
| 6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0046) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (Click here).
Turn the ignition switch off.
Remove the EFI fuse from the engine room relay block and junction block assembly for more than 1 minute.
Turn the ignition switch to ON and wait for 10 seconds or more.
Start the engine.
Drive the vehicle with a city driving pattern at least 10 minutes.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P0046 is output | A |
| No DTC is output | B |
|
| ||||
| A | ||
| ||
| 7.REPLACE TURBOCHARGER SUB-ASSEMBLY |
Replace turbocharger sub-assembly (Click here).
|
| ||||
| 8.REPLACE TURBO MOTOR DRIVER |
Replace turbo motor driver .
|
| ||||
| 9.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (Click here).
Turn the ignition switch off.
Remove the EFI fuse from the engine room relay block and junction block assembly for more than 1 minute.
Turn the ignition switch to ON and wait for 10 seconds or more.
Start the engine.
Drive the vehicle with a city driving pattern at least 10 minutes.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||