Home › ENGINE ยท 2KD-FTV › INTAKE › TURBOCHARGER

TURBOCHARGER > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE INTERCOOLER ASSEMBLY
(Click here)


3. REMOVE NO. 1 ENGINE UNDER COVER


4. REMOVE NO. 2 ENGINE UNDER COVER


5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



    A099591
  1. Drain the coolant by removing the radiator reservoir cap and, using a wrench, remove the vent plug.



  1. Loosen the cylinder block drain cock plug.


    A112147E03


    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Radiator Reservoir Cap
    *3
    Vent Plug
    *4
    Cylinder Block Drain Cock Plug
    *5
    Radiator Drain Cock Plug
    -
    -



6. REMOVE FRONT FENDER APRON SEAL UPPER
  1. Remove the 5 clips and front fender apron seal upper.



7. REMOVE FRONT FENDER SEAL
  1. Remove the 5 clips and front fender seal.



8. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.

  1. Disconnect the front exhaust pipe from the turbine outlet elbow and remove the gasket.

  1. Remove the front exhaust pipe from the exhaust pipe support.



9. REMOVE AIR CLEANER ASSEMBLY
  1. Disconnect the mass air flow meter connector.

  1. Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner.



10. REMOVE VENTILATION PIPE


    A211832
  1. Remove the bolt and disconnect the 2 ventilation hoses and ventilation pipe.



11. REMOVE COMPRESSOR INLET ELBOW


    A211833
  1. Disconnect the 2 connectors from the turbocharger.

  1. Detach the wire harness clamp.

  1. Remove the 2 nuts, compressor inlet elbow and gasket.



12. REMOVE NO. 1 TURBO INSULATOR


    A255740
  1. Remove the 2 bolts and No. 1 turbo insulator.



13. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A255741
  1. Remove the bolt and No. 1 exhaust manifold heat insulator.



14. REMOVE NO. 1 TURBO WATER HOSE


    A211835
  1. Remove the 2 No. 1 turbo water hoses.



15. REMOVE TURBINE OUTLET ELBOW


    A211836
  1. Remove the 3 nuts, turbine outlet elbow and gasket.



16. REMOVE TURBOCHARGER STAY


    A211837
  1. Remove the 2 bolts, nut and turbocharger stay.



17. REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY


    A211838E01
  1. Remove the 2 bolts, 2 nuts, union bolt, turbo oil inlet pipe and 3 gaskets.

    NOTICE:
    Do not loosen the nut labeled A.



18. REMOVE TURBOCHARGER SUB-ASSEMBLY


    A211839
  1. Remove the 3 nuts, turbocharger and gasket.



19. REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY


    A211906
  1. Remove the bolt, 2 nuts, No. 1 turbo water pipe and gasket.