Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > Microphone Circuit between Microphone and Radio Receiver

for Preparation Click here


DESCRIPTION

Microphone signal from the telephone microphone assembly is sent to the radio and display receiver assembly. Also, power is supplied from the radio and display receiver assembly to the telephone microphone assembly.

WIRING DIAGRAM


E277658E10


INSPECTION PROCEDURE

1.CHECK TELEPHONE MICROPHONE ASSEMBLY (OPERATION CHECK)


    E268457
  1. Enter the "Microphone Check" screen. [Refer to Microphone and Voice Recognition Check in Operation Check (Click here)]

  1. When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

  1. Push the recording switch and perform voice recording.

    HINT:
    1. Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.
    2. Voice can be recorded for up to 5 seconds.

  1. w/ Recording Function:
    Check that the recording indicator remains on while recording and that the recorded voice is played normally without noise or distortion.

    OK:
    All check results are normal.



NG
Go to step 2
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)  

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
  1. Disconnect the R19 radio and display receiver assembly connector.

  1. Disconnect the M4 map light assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R19-4 (MACC) - M4-4 (MACC)
    Always
    Below 1 Ω
    R19-5 (MIN+) - M4-3 (MCO+)
    Always
    Below 1 Ω
    R19-19 (MIN-) - M4-2 (MCO-)
    Always
    Below 1 Ω
    R19-6 (SNS2) - Body ground
    Always
    Below 1 Ω
    R19-4 (MACC) - Body ground
    Always
    10 kΩ or higher
    R19-5 (MIN+) - Body ground
    Always
    10 kΩ or higher
    R19-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    R19-18 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY


    E280108E20
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R19-18 (SGND) - Body ground
    Always
    Below 1 Ω
    R19-19 (MIN-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R19-4 (MACC) - Body ground
    Ignition switch ACC
    4 to 6 V

Text in Illustration 
*a
Component with harness connected
(Radio and Display Receiver Assembly)


NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


4.CHECK TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.



NG
REPLACE MAP LIGHT ASSEMBLY (Click here)
OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)