Home › ENGINE ยท 2KD-FTV › FUEL › COMMON RAIL

COMMON RAIL > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE DIESEL THROTTLE BODY ASSEMBLY
(Click here)


3. REMOVE NO. 1 ENGINE UNDER COVER


4. REMOVE NO. 2 ENGINE UNDER COVER


5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

  1. Wipe the oil pan and drain plug.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }



6. REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE


    A211857
  1. Disconnect the vacuum switching valve connector.



    A211858
  1. Disconnect the 3 vacuum transmitting hoses.



    A211859
  1. Remove the 2 bolts and manifold stay with vacuum switching valve.



7. REMOVE OIL FILTER SUB-ASSEMBLY


    A227248E01
  1. Using SST, remove the oil filter.

    SST
    09228-07501  

    HINT:
    Insert the drain hose in the oil filter. Put the disposal container beneath the drain hose to collect the oil from the oil filter.



8. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.



    A211871
  1. Remove the 2 nuts and No. 3 injection pipe clamp.



    A211872
  1. Remove the 2 bolts and 2 No. 2 injection pipe clamps.



    A211873E02
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
    Text in Illustration 
    *a
    Injector Side
    *b
    Common Rail Side



9. REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET


    A147215
  1. Remove the 3 bolts and No. 2 intake air connector bracket.



10. DISCONNECT NO. 3 WATER BY-PASS PIPE


    A147216
  1. Remove the 2 bolts and disconnect the No. 3 water by-pass pipe with the wire harness.



11. REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (for EGR)


    A211846
  1. Disconnect the 2 connectors.



    A252294
  1. Disconnect the 6 vacuum hoses.

  1. Remove the bolt and No. 1 gas filter with gas filter bracket.



    A211848
  1. Remove the 2 bolts and electric vacuum regulating valve.



12. REMOVE NO. 2 INTAKE AIR CONNECTOR


    A147230
  1. Remove the 3 nuts, No. 2 intake air connector and gasket.



13. REMOVE INTAKE AIR CONNECTOR


    A147219
  1. Remove the 3 bolts, intake air connector and 2 gaskets.



14. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 1 EGR PIPE SUB-ASSEMBLY


    A211879
  1. Remove the 2 nuts, electric EGR control valve with No. 1 EGR pipe and gasket.



15. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY


    A152275
  1. Remove the bolt and disconnect the injection pipe clamp.

    NOTICE:
    If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.



    A152276E07
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
    Text in Illustration 
    *a
    Injector Side
    *b
    Common Rail Side



16. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
  1. Disconnect the 3 fuel hoses.



    A152338E04
  1. Remove the union bolt, 3 bolts, No. 2 nozzle leakage pipe and gasket.
    Text in Illustration 
    *1
    Union Bolt



17. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the engine oil level dipstick.



    A148132
  1. Remove the bolt and injection pipe clamp.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.



18. REMOVE FUEL INLET PIPE SUB-ASSEMBLY


    A098969E11
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
    Text in Illustration 
    *a
    Common Rail Side
    *b
    Fuel Supply Pump Side



19. REMOVE COMMON RAIL ASSEMBLY
  1. Disconnect the 2 connectors.



    A231856
  1. Remove the 2 bolts, common rail and No. 2 intake manifold insulator.

    NOTICE:
    Do not remove the pressure discharge valve or pressure sensor.