Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM (w/ VSC)

CAN COMMUNICATION SYSTEM (w/ VSC) > Open in CAN Main Bus Line


DESCRIPTION

There may be an open circuit in the CAN main wire and/or the DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher.
  1. CAN main wire and connector
  2. No. 1 junction connector
  3. No. 2 junction connector
  4. No. 3 junction connector
  5. ECM
  6. DLC3 branch wire or connector

WIRING DIAGRAM


C234155E02


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    For vehicles with SRS:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2.CHECK OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - DLC3)


    C190792E18
  1. Disconnect the J51 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J51-2 (CANH) - D3-6 (CANH)
    Ignition switch off
    Below 1 Ω
    J51-1 (CANL) - D3-14 (CANL)
    Ignition switch off
    Below 1 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3.CONNECT CONNECTOR
  1. Reconnect the J51 No. 3 junction connector connector.


NEXT


4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)


    C190785E07
  1. Disconnect the J57 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J57-4 (CANH) - J57-1 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 6
OK


5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - ECM)


    C190785E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J57-12 (CANH) - J57-6 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 11
OK

REPLACE NO. 1 JUNCTION CONNECTOR 

6.CONNECT CONNECTOR
  1. Reconnect the J57 No. 1 junction connector connector.


NEXT


7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)


    C190786E07
  1. Disconnect the J56 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J56-3 (CANH) - J56-7 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 9
OK


8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)


    C190786E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J56-1 (CANH) - J56-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK

REPLACE NO. 2 JUNCTION CONNECTOR 

9.CONNECT CONNECTOR
  1. Reconnect the J56 No. 2 junction connector connector.


NEXT


10.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C190789E08
  1. Disconnect the J52 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J52-2 (CANH) - J52-1 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 3 JUNCTION CONNECTOR 

11.CONNECT CONNECTOR
  1. Reconnect the J57 No. 1 junction connector connector.


NEXT


12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 1 JUNCTION CONNECTOR)


    C190783E04
  1. for 1KD-FTV, 2KD-FTV:

    1. Disconnect the E5 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      E5-24 (CANH) - E5-23 (CANL)
      Ignition switch off
      108 to 132 Ω



    F100904E08
  1. for 1GR-FE:

    1. Disconnect the E13 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      E13-33 (CANH) - E13-34 (CANL)
      Ignition switch off
      108 to 132 Ω

Result 
Result
Proceed to
OK (for 1KD-FTV)
A
OK (for 2KD-FTV)
B
OK (for 1GR-FE)
C
NG
D


B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 1 JUNCTION CONNECTOR)
A

REPLACE ECM (Click here)