Home › BODY › INSTRUMENT PANEL › LOWER INSTRUMENT PANEL

LOWER INSTRUMENT PANEL > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


  1. for LHD:

    1. Attach the 2 guides to install the lower instrument panel.

    2. Connect the connectors and attach the clamps.

    3. Connect the hood lock control cable, fuel lid lock control cable and DLC3.

    4. Install the 2 bolts <C>, nut <D> and 3 screws <E>.



    5. Install the 2 clips <B>.


      B278247E01


      Text in Illustration 
      *1
      Clip <B>
      *2
      Bolt <C>
      *3
      Nut <D>
      *4
      Screw <E>
      *5
      Hood Lock Control Cable
      *6
      Fuel Lid Lock Control Cable
      *7
      DLC3
      *8
      Clamp
      *9
      Guide
      -
      -



  1. for RHD:

    1. Attach the 2 guides to install the lower instrument panel.

    2. Connect the connectors and attach the clamps.

    3. Connect the hood lock control cable, fuel lid lock control cable and DLC3.

    4. Install the 2 bolts <C>, nut <D> and 3 screws <E>.



    5. Install the 2 clips <B>.


      B278248E01


      Text in Illustration 
      *1
      Clip <B>
      *2
      Bolt <C>
      *3
      Nut <D>
      *4
      Screw <E>
      *5
      Hood Lock Control Cable
      *6
      Fuel Lid Lock Control Cable
      *7
      DLC3
      *8
      Clamp
      *9
      Guide
      -
      -



2. INSTALL NO. 1 SWITCH HOLE BASE
  1. Attach the 5 claws to install the No. 1 switch hole base.



3. INSTALL SWITCH BASE
  1. Connect the connectors.

  1. Attach the 9 claws and guide to install the switch base.



4. INSTALL AIR CONDITIONER CONTROL ASSEMBLY (for Manual Air Conditioning System)
  1. Connect the connector and install the air conditioning control assembly.



5. INSTALL NO. 1 INSTRUMENT PANEL BOX
  1. Connect the connectors and attach the clamp.

  1. Install the No. 1 instrument panel box with the 6 screws <A>.



6. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
  1. Attach the 3 guides, 2 claws and 3 clips to install the lower instrument panel finish panel.



7. INSTALL NO. 3 HEATER TO REGISTER DUCT
  1. Attach the 4 claws to install the No. 3 heater to register duct.

  1. Install the clip.



8. INSTALL NO. 1 HEATER TO REGISTER DUCT
  1. Attach the 3 claws to install the No. 1 heater to register duct.

  1. Install the clip.



9. INSTALL NO. 2 HEATER TO REGISTER DUCT
  1. Install the No. 2 heater to register duct with the 3 clips.



10. INSTALL COWL SIDE TRIM BOARD LH
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the clip.

  1. Install the front door opening trim.



11. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure described for the LH side.



12. INSTALL FRONT DOOR SCUFF PLATE LH
  1. Attach the 3 clips and 7 claws to install the front door scuff plate.



13. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



14. INSTALL CONSOLE BOX ASSEMBLY
(Click here)


15. INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY
(Click here)


16. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



18. CHECK SRS WARNING LIGHT
(Click here)