Home › ENGINE ยท 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0400    Exhaust Gas Recirculation Flow

for Preparation Click here


DESCRIPTION

The EGR system recirculates exhaust gases, and performs control so that the proper volume of exhaust gas is recirculated to suit all driving conditions. The recirculated gas mixes with the intake air, allowing the EGR system to slow down engine combustion and lower the combustion temperature. This helps reduce NOx emissions.
In order to increase circulation efficiency, the ECM adjusts the lift amount of the EGR valve and throttle valve.

P0400 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Decelerate from a speed of 50 km/h (80 mph) or more (release accelerator pedal for approximately 5 seconds)
Mass air flow rate is not changed when the EGR valve is turned on (2 trip detection logic).
  1. EGR valve stuck
  2. EGR valve does not move smoothly
  3. Electric vacuum regulating valve assembly
  4. Vacuum switching valve (for EGR Cut)
  5. Electric vacuum regulating valve assembly circuit
  6. Vacuum switching valve (for EGR Cut) circuit
  7. EGR blockage in line between exhaust manifold and intake manifold
  8. Mass air flow meter
  9. Intake system (leaks or blockages)
  10. Exhaust system (exhaust gas leaks)
  11. ECM

Related Data List 
DTC No.
Data List
P0400
  1. MAF
  2. MAP
  3. Actual EGR Valve Pos.
  4. Target EGR Position
  5. EGR Close Lrn. Val.
  6. EGR Close Learn Val.
  7. EGR Close Lrn. Status
  8. EGR Lift Sensor Volt %

MONITOR DESCRIPTION

  1. If the electric EGR control valve assembly is forcibly operated but the intake air amount does not vary, the ECM determines that the electric EGR control valve assembly is malfunctioning. The ECM then illuminates the MIL.
Flow malfunction
  1. If the EGR valve is forcibly operated during deceleration but the intake air amount does not vary, the ECM determines that the EGR valve is malfunctioning. The ECM then illuminates the MIL (2 trip detection logic).

A194528E03


WIRING DIAGRAM


A255065E04


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedures.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0400)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P0400 is output
    A
    P0400 and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE EGR VALVE CLOSE)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.

  1. Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

  1. Read the MAF value displayed on the tester while the engine is idling.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EGR Valve Close.

  1. Read the MAF value when the EGR valve is closed using the Active Test function.

    HINT:
    1. If idling continues for 15 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or to restart the engine.
    2. Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.


    Result 
    Active Test
    Result
    Proceed to
    Activate the EGR Valve Close:
    Off (Open) to on (Closed)
    MAF value does not change
    A
    MAF value changes
    B

    NOTICE:
    As the values shown below may differ due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.

    HINT:
    The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric vacuum regulating valve assembly, electric EGR control valve assembly or mass air flow meter.


    Reference:

    EGR Valve Condition (Opening)
    Measuring Condition
    MAF (Reference)
    Open (55%)
    1. Atmosphere pressure: 101 kPa
    2. Intake air temperature: 30°C (86°F)
    3. Engine coolant temperature: 88°C (190°F)
    3.0 to 9.0 gm/s
    Close (0%)
    15 to 22 gm/s



B
Go to step 6
A


3.CHECK VACUUM HOSES
  1. Check the vacuum hoses.

OK:
The hoses are not damaged and are securely connected



NG
Go to step 8
OK


4.INSPECT ELECTRIC VACUUM REGULATING VALVE ASSEMBLY
  1. Inspect the electric vacuum regulating valve assembly (Click here).

HINT:
Before replacing the electric vacuum regulating valve assembly, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



NG
Go to step 9
OK


5.INSPECT VACUUM SWITCHING VALVE (FOR EGR CUT)
  1. Inspect the vacuum switching valve (for EGR cut) (Click here).

    HINT:
    Before replacing the vacuum switching valve (for EGR cut), perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



NG
Go to step 10
OK


6.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (EGR VALVE OPERATION)
  1. Inspect the electric EGR control valve assembly (Click here).

OK:
The valve is not stuck and does not have heavy carbon deposits



NG
Go to step 9
OK


7.CHECK FOR DEPOSIT (EGR PASSAGE)
  1. Check for blockage in the EGR gas passage between the exhaust manifold and electric EGR control valve assembly.

OK:
No blockage in the EGR gas passage



OK
Go to step 12

NG
Go to step 11

8.REPAIR OR REPLACE VACUUM HOSE
  1. Repair or replace the vacuum hose.



NEXT
Go to step 12

9.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
  1. Replace the electric EGR control valve assembly (Click here).



NEXT
Go to step 12

10.REPLACE VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR CUT)
  1. Replace the vacuum switching valve (for EGR cut) (Click here).



NEXT
Go to step 12

11.REPAIR OR REPLACE MALFUNCTIONING PARTS

NEXT


12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs. (Click here)

  1. Turn the ignition switch off for 30 seconds or more.

  1. Start the engine and warm it up.

  1. Move the shift lever to 2nd gear and decelerate from a speed of 50 km/h (31 mph) or more (fully release the accelerator for approximately 5 seconds or more).

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

HINT:
When a DTC is output, the mass air flow meter may be malfunctioning.


NEXT

END