2014 Hilux · Service Manual CRUISE CONTROL SYSTEM

DATA LIST / ACTIVE TEST

System information · Vehicles built from Jun 2011


READ DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Powertrain / Cruise Control / Data List.

  5. According to the display on the intelligent tester, read the "Data List".

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    CCS Vehicle Spd
    Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)
    Actual vehicle speed displayed
    -
    CCS Mem Vehicle Spd
    Memory vehicle speed / min.: 0 km/h (0 mph), max.: 200 km/h (125 mph)
    Actual vehicle speed stored in memory
    -
    Throttle Opening Angle*1
    Throttle opening angle / min.: 0 deg, max.: 125 deg
    Actual required throttle opening angle
    -
    Throttle Opening Angle*2
    Throttle opening angle / min.: 0%, max.: 100%
    Actual required throttle opening angle
    -
    Cruise Control
    Cruise control system active condition / ON or OFF
    ON: Cruise control system activated
    OFF: Cruise control system inactivated
    -
    CCS Main SW M-CPU
    Cruise control main switch signal (Main CPU) / ON or OFF
    ON: Cruise control main switch (Main CPU) on
    OFF: Cruise control main switch (Main CPU) off
    -
    CCS Ready M-CPU
    Cruise control system standby condition (Main CPU) / ON or OFF
    ON: Cruise control main switch (Main CPU) on
    OFF: Cruise control main switch (Main CPU) off
    -
    CCS Indicator M-CPU
    Cruise control indicator light signal (Main CPU) / ON or OFF
    ON: Cruise control indicator light (Main CPU) on
    OFF: Cruise control indicator light (Main CPU) off
    -
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    (-SET) switch signal / ON or OFF
    ON: (-SET) switch on
    ON: (-SET) switch off
    -
    RES/ACC Switch
    (+RES) switch signal / ON or OFF
    ON: (+RES) switch on
    OFF: (+RES) switch off
    -
    Stop Light SW M-CPU
    Stop light switch signal (Main CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Cruise Operation Status*3
    PNP switch signal (D position) ON or OFF
    ON: Shift lever on D or 4
    OFF: Shift lever not on D or 4
    -
    Cruise Operation Status*4
    PNP switch signal (D position) ON or OFF
    ON: Shift lever on D or 3
    OFF: Shift lever not on D or 3
    -
    1. *1: for 1GR-FE
    2. *2: for 1KD-FTV
    3. *3: for A750E, A750F Automatic Transmission
    4. *4: for A340F Automatic Transmission

← FAIL-SAFE CHART (from Jun 2011)DIAGNOSTIC TROUBLE CODE CHART (Jun 2011 – Jul 2012) →