2014 Hilux · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. TABLE OF BOLT, SCREW AND NUT

  1. All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with an alphabetical code in the table.

    B277625E01


2. PRECAUTION (w/ Airbag System)

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


4. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)

5. REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY
(Click here)

6. REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box)
(Click here)

7. REMOVE FRONT DOOR SCUFF PLATE LH
  1. for Double Cab:
    (Click here)

  1. for Single Cab:
    (Click here)

  1. for Extra Cab:
    (Click here)


8. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.


9. REMOVE COWL SIDE TRIM BOARD LH

B277609
  1. Remove the part of the front door opening trim attached to the cowl side trim board.

  1. Remove the clip.

  1. Detach the 2 clips and remove the cowl side trim.


10. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure described for the LH side.


11. REMOVE NO. 2 HEATER TO REGISTER DUCT

  1. E225181
    Remove the 3 clips and No. 2 heater to register duct.


12. REMOVE NO. 1 HEATER TO REGISTER DUCT

E225182
  1. Remove the clip.

  1. Detach the 3 claws and remove the No. 1 heater to register duct.


13. REMOVE NO. 3 HEATER TO REGISTER DUCT

E225183
  1. Remove the clip.

  1. Detach the 4 claws and remove the No. 3 heater to register duct.


14. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

B278242
  1. Detach the 2 claws, 3 clips and 3 guides and remove the lower instrument panel finish panel.


15. REMOVE NO. 1 INSTRUMENT PANEL BOX

B278243
  1. Remove the 6 screws <A>.

  1. Disconnect the connectors, detach the clamp and remove the No. 1 instrument panel box.


16. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Manual Air Conditioning System)
  1. Disconnect the connector and remove the air conditioning control assembly.


17. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL (w/o Console Box)

B278244
  1. Using a clip remover, remove the 2 clips <B>.

  1. Detach the 3 claws and remove the lower center instrument panel finish panel.


18. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (w/o Front Passenger Airbag)

B278058E01
  1. Slightly bend the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.

    Text in Illustration 
    *1
    Stopper

  1. B278059E01
    Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.
    Text in Illustration 
    *1
    Hinge


19. REMOVE SWITCH BASE

B278245
  1. Detach the 8 claws.

    HINT:
    If the claws are difficult to detach, detach the claws from the back of the switch base.

  1. Disconnect the connectors and remove the switch base..


20. REMOVE NO. 1 SWITCH HOLE BASE

B278246E01
  1. Put protective tape around the No. 1 switch hole base.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 5 claws.

  1. Disconnect the connectors and remove the No. 1 switch hole base.


21. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. for LHD:

    1. Using a clip remover, remove the 2 clips <B>.

    2. Remove the 2 bolts <C>, nut <D> and 3 screws <E>.

    3. Disconnect the hood lock control cable, fuel lid lock control cable and DLC3.

    4. Disconnect the connectors and detach the clamps.

    5. Detach the 2 guides and remove the lower instrument panel.

      B278247E01

      Text in Illustration 
      *1
      Clip <B>
      *2
      Bolt <C>
      *3
      Nut <D>
      *4
      Screw <E>
      *5
      Hood Lock Control Cable
      *6
      Fuel Lid Lock Control Cable
      *7
      DLC3
      *8
      Clamp
      *9
      Guide
      -
      -

  1. for RHD:

    1. Using a clip remover, remove the 2 clips <B>.

    2. Remove the 2 bolts <C>, nut <D> and 3 screws <E>.

    3. Disconnect the hood lock control cable, fuel lid lock control cable and DLC3.

    4. Disconnect the connectors and detach the clamps.

    5. Detach the 2 guides and remove the lower instrument panel.

      B278248E01

      Text in Illustration 
      *1
      Clip <B>
      *2
      Bolt <C>
      *3
      Nut <D>
      *4
      Screw <E>
      *5
      Hood Lock Control Cable
      *6
      Fuel Lid Lock Control Cable
      *7
      DLC3
      *8
      Clamp
      *9
      Guide
      -
      -

← COMPONENTS (from Jun 2011)REMOVAL (Aug 2012 – Jul 2013) →