Home › BODY › INTERIOR › ROOF HEADLINING (for Single Cab)
REMOVAL
Removal / installation · Vehicles built Jun 2011 – Jul 2012
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
HINT:
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1.
PRECAUTION (w/ Airbag System)
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here ).
2.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here ).
3.
REMOVE FRONT SEAT ASSEMBLY LH
w/ Front Seat Side Airbag: (Click here )
for Separate Seat Type: (Click here )
4.
REMOVE FRONT SEAT ASSEMBLY RH
w/ Front Seat Side Airbag:
HINT:
Use the same procedure described for the LH side.
for Separate Seat Type:
HINT:
Use the same procedure described for the LH side.
for Bench Seat Type: (Click here )
5.
REMOVE FRONT DOOR SCUFF PLATE LH
Put protective tape around the front door scuff plate.
Text in Illustration
*1
Protective Tape
Using a moulding remover, detach the 4 clips and 8 claws and remove the front door scuff plate.
6.
REMOVE FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedure described for the LH side.
7.
REMOVE FRONT DOOR OPENING TRIM LH
Remove the front door opening trim.
8.
REMOVE FRONT DOOR OPENING TRIM RH
HINT:
Use the same procedure described for the LH side.
9.
REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH (w/ Assist Grip)
HINT:
Use the same procedure for both front No. 1 assist grip plugs.
Using a screwdriver, detach the 2 claws and remove the front No. 1 assist grip plug.
HINT:
Tape the screwdriver tip before use.
Text in Illustration
*1
Protective Tape
10.
REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH (w/ Assist Grip)
HINT:
Use the same procedure described for the LH side.
11.
REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)
HINT:
Use the same procedure for both front assist grips.
Remove the 2 screws and front assist grip.
12.
REMOVE FRONT PILLAR GARNISH LH
Detach the 2 clips and 2 guides and remove the front pillar garnish.
w/ Curtain Shield Airbag: Protect the curtain shield airbag assembly.
Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.
NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
Text in Illustration
*1
Protective Cover
*2
Adhesive Tape
13.
REMOVE FRONT PILLAR GARNISH RH
HINT:
Use the same procedure described for the LH side.
14.
REMOVE UPPER BACK PANEL GARNISH
Detach the 4 claws, 4 guides and 5 clips and remove the upper back panel garnish.
15.
REMOVE LOWER QUARTER TRIM PANEL LH
Remove the bolt and disconnect the front seat outer belt floor anchor.
Detach the claw, 3 clips and 2 guides and remove the lower quarter trim panel.
16.
REMOVE LOWER QUARTER TRIM PANEL RH
HINT:
Use the same procedure described for the LH side.
17.
REMOVE QUARTER INSIDE TRIM BOARD LH
Using a screwdriver, detach the 2 claws and open the front seat belt shoulder anchor cover.
HINT:
Tape the screwdriver tip before use.
Text in Illustration
*1
Protective Tape
Remove the bolt and disconnect the front seat belt shoulder anchor.
Detach the 3 clips and remove the quarter inside trim board.
18.
REMOVE QUARTER INSIDE TRIM BOARD RH
HINT:
Use the same procedure described for the LH side.
19.
REMOVE NO. 1 ROOM LIGHT ASSEMBLY
Connect the light connector.
Install the room light with the 2 screws.
Attach the lens with the 4 claws.
20.
REMOVE VISOR ASSEMBLY LH
Detach the guide.
Remove the 2 screws and visor.
21.
REMOVE VISOR ASSEMBLY RH
HINT:
Use the same procedure described for the LH side.
22.
REMOVE VISOR HOLDER LH
Remove the screw.
Detach the 2 claws and remove the visor holder.
23.
REMOVE VISOR HOLDER RH
HINT:
Use the same procedure described for the LH side.
24.
REMOVE ASSIST GRIP (w/ Assist Grip)
Using a screwdriver, detach the 4 claws and open the 2 covers.
HINT:
Tape the screwdriver tip before use.
Text in Illustration
*1
Protective Tape
Remove the 2 screws and assist grip.
25.
REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here )
26.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
Detach the 2 claws, 3 clips and 3 guides and remove the lower instrument panel finish panel.
27.
REMOVE NO. 2 HEATER TO REGISTER DUCT
Remove the 3 clips and No. 2 heater to register duct.
28.
REMOVE NO. 1 HEATER TO REGISTER DUCT
Remove the clip.
Detach the 3 claws and remove the No. 1 heater to register duct.
29.
REMOVE NO. 3 HEATER TO REGISTER DUCT
Remove the clip.
Detach the 4 claws and remove the No. 3 heater to register duct.
30.
REMOVE DEFROSTER NOZZLE ASSEMBLY (w/ Defroster)
Using a screwdriver, detach the 4 clips and remove the defroster nozzle assembly.
Remove the defroster nozzle assembly.
31.
REMOVE ROOF HEADLINING ASSEMBLY
Detach the 4 clamps from the front pillar.
for LHD:
Disconnect the connectors and detach the 4 clamps.
Using a clip remover, remove the 5 clips.
Remove the roof headlining as shown in the illustration.
NOTICE:
Be careful not to damage the roof headlining when removing it.
for RHD:
Disconnect the connectors and detach the 5 clamps.
Using a clip remover, remove the clips.
Text in Illustration
*A
w/o Assist Grip
Remove the roof headlining as shown in the illustration.
NOTICE:
Be careful not to damage the roof headlining when removing it.
32.
REMOVE FRONT SIDE RAIL SPACER LH
Detach the 2 claws and remove the front side rail spacer.
33.
REMOVE FRONT SIDE RAIL SPACER RH
HINT:
Use the same procedure described for the LH side
34.
REMOVE SIDE RAIL SPACER (for LHD)
Detach the 2 claws and remove the side rail spacer.
35.
REMOVE SIDE RAIL SPACER (for RHD)
HINT:
Use the same procedure described for the LHD.
36.
REMOVE REAR NO. 2 SIDE RAIL SPACER LH
Detach the 2 claws and remove the rear No. 2 side rail spacer.
37.
REMOVE REAR NO. 2 SIDE RAIL SPACER RH
HINT:
Use the same procedure described for the LH side.