2014 Hilux · Service Manual ENGINE

P0617 Starter Relay Circuit High

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.
If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) for more than 20 seconds.
DTC No.
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) are met, positive (+B) battery voltage of 10.5 V or more applied to ECM for 20 seconds
(1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.4 mph)
(b) Engine speed is more than 1,000 rpm
(c) STA signal is ON
  1. Starter relay circuit
  2. Ignition switch
  3. ECM

WIRING DIAGRAM

A222525E03

INSPECTION PROCEDURE

NOTICE:
If the ECM is replaced, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. The following troubleshooting process is based on the premise that the engine is cranked normally. If the engine will not crank, proceed to the problem symptoms table (Click here).
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.

    OK:
    Ignition Switch Condition
    Tester Display (Starter Signal)
    ON
    OFF
    START
    ON



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2. INSPECT IGNITION SWITCH ASSEMBLY
  1. Disconnect the ignition switch connector.

  1. G035048E09
    Measure the resistance of the ignition switch.

    Standard resistance:
    Tester Condition
    Switch Condition
    Specified Condition
    5 (AM2) - 7 (ST2)
    LOCK
    10 kΩ or higher
    5 (AM2) - 7 (ST2)
    START
    Below 1 Ω

  1. Reconnect the ignition switch connector.



OK
Go to step 5
NG


3. REPLACE IGNITION SWITCH ASSEMBLY
  1. Replace the ignition switch assembly (Click here).


NEXT


4. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.

    OK:
    Ignition Switch Condition
    Tester Display (Starter Signal)
    ON
    OFF
    START
    ON



OK
SYSTEM IS OK
NG


5. REPAIR OR REPLACE HARNESS AND CONNECTOR (IGNITION SWITCH - STA TERMINAL OF ECM)

NEXT


6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the tester ON.

  1. Clear DTCs (Click here).

  1. Drive the vehicle at more than 12.4 mph (20 km/h) for over 20 seconds.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0617
    A
    No DTC
    B



B
SYSTEM IS OK
A

REPLACE ECM


← P0607 Control Module Performance (+ P1611) (from Aug 2014)P0617 Starter Relay Circuit High (Aug 2012 – Jul 2013) →