2014 Hilux · Service Manual TRANSMISSION

P0617 Starter Relay Circuit High

Diagnostic trouble codes · Vehicles built from Aug 2012

Versions by build date: Jun 2011 – Jul 2012 from Aug 2012

DESCRIPTION

While the engine is being cranked, battery voltage is applied to terminal STA of the TCM.
If the TCM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The TCM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle is driven at more than 20 km/h (12.4 mph) for over 20 seconds.
DTC Code
DTC Detection Condition
Trouble Area
P0617
All conditions are met (1-trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.4 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is ON.
(d) Battery voltage (10.5 V or higher) is applied to the TCM for 20 seconds.
  1. Park/neutral position switch
  2. Starter relay circuit
  3. TCM

WIRING DIAGRAM

C229622E21

INSPECTION PROCEDURE

HINT:
The following troubleshooting flowchart is based on the premise that the engine can be cranked normally. If the engine does not crank, proceed to the problem symptoms table.


1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / ECT / Data List.

  1. Read the value displayed on the intelligent tester.

  1. Crank the engine.

  1. Read the value displayed on the intelligent tester.

    ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Starter Signal
    Starter signal/
    ON or OFF
    1. ON: Engine cranking
    2. OFF: Engine not cranking
    -

    OK:
    Starter Signal is only ON when the engine is being started (during cranking).



NG
Go to step 2
OK

CHECK INTERMITTENT PROBLEMS

2. CHECK TCM (STA VOLTAGE)

  1. C229623E01
    Disconnect the T19 TCM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    T19-11 (STA) - T19-1 (E1)
    Ignition switch ON and shift lever in P or N
    Below 2 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C146745E60
    Disconnect the N8 park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (B) - 5 (L)
    Shift lever in P
    Below 1 Ω
    4 (B) - 5 (L)
    Shift lever in N
    Below 1 Ω
    4 (B) - 5 (L)
    Shift lever not in P
    10 kΩ or higher
    4 (B) - 5 (L)
    Shift lever not in N
    10 kΩ or higher
    2 (RB) - 5 (L)
    Shift lever in P, R, N, D, 3, 2 or L
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
OK

REPLACE TCM


← P0617 Starter Relay Circuit High (Jun 2011 – Jul 2012)P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) (Jun 2011 – Jul 2012) →